flat washers 5310-081-4219, six 5/16-inch split
the shop van for transportation purposes
lockwashers 5310-407-9566, and six 5/16-18
only and is to be removed from the van
hexagon plain nuts 5310-880-7744.
before operation.
(4) Secure each of the table tops to angle iron
(factory installed in van) with two 5/8-11 x 3-
f. Nitrogen Tank Support Block (figs. 1, 3 and 4)
1 / 4 - i n c h hexagon-head capscrews 5305-724-
(1) Fabricate three 24 inch long support
7236, two 21/32-inch inside diameter flat washers
blocks (designated I) as shown in figure 4. The
5310-823-8803, and two 5/8-inch split lock-
blocks are to be placed on the left side of the van 8
washers 5310-045-5001 (nuts are factory installed
inches from the rear wall.
in table top).
(2) One block is to be placed 35-1/2 inches
above the floor (directly beneath angle iron). Mark
b. Portable Electrical Grinder (Figs 1 and
3).
and drill 1/2-inch holes through block ap-
Place the portable electrical grinder 5130-293-
proximately two inches from each end (aligned with
2488 (designated B) on work table (A) and
holes in angle iron). Secure with two 7/16-20x 5-
position the base of the grinder 10 inches from the
1/2-inch hexagon-head machine bolts 5306-177-
right end and 2 inches from the front edge of the
5677, two 1/2-inch inside diameter flat washers
table top as shown in figure 1. Mark and drill four
11/32-inch holes through the table top aligned
5310-905-5454, and two 7/16-20 hexagon plain
with mounting holes in the base of the grinder.
nuts 5310-741-5305.
Secure the grinder with four 5/16-18 x 3-1/2-
inch square neck bolts 5306-058-0518, four
(3) Two blocks are to be positioned on the
floor, one flush with the wall and one directly in
11/32-inch inside diameter flat washers 5310-
front of the other so that nitrogen tank will fit
snugly between them. Mark and drill, two inches
407-9566, and four 5/16-18 hexagon plain nuts
from each end of blocks, 1/2 inch holes through
5310-880-7744.
blocks and floor of van. Secure each block with two
c. Machinist's Vise (Figs. 1 and
2). Place the
7/16-20 x 8-inch hexagon-head machine bolts
machinist vise 5120-293-1439 (designated D ) on
5306-027-5803, two 1/2-inch inside diameter flat
work table (C), and position the base of the stand 4
washers 5310-760-2021, two 7/16-inch split lock-
inches from the right end of the table top and flush
w a s h e r s 5310-905-5454, and two 7/16-20
with the front edge as shown in figure 1. Mark and
hexagon plain nuts 5310-741-5305.
drill four 9/16-inch holes in the base of the vise.
(4) Secure nitrogen tank (designated H) to
Secure the vise with four 1/2-13 x 3-1/2-inch
upper block with webbing strap. Fabricate strap
square neck bolts 5306-702-2821, four 17/32-
using webbing 8305-263-2477 and a buckle 5340-
inch inside diameter flat washers 5310-809-5998,
850-8060. Position and secure two strap fastener
four 1/2-inch split lockwashers 5310-584-5272,
loops 5340-616-4660 at opposite ends of block with
and four 1/2-13 hexagon plain nuts 5310-834-
two no. 10-2-1/2 inch round head wood screws
8732.
5305-013-0384 and two .234 inch inside diameter
d. Portable Electric Drill and
Stand (Figs 1 and
flat washers 5310-273-7729. Loop webbing strap
2). Place the drill and stand 5130-204-2718
through fastener loops and buckle as required to
(designated F) on work table (E), and position the
hold tank firmly in position as shown in figure 3.
base of the stand 10 inches from the right end of the
g. Pump Kits (Fig. 2). Place the two pump kits
table top and 1 inch from the front edge as shown in
4933-712-2378 (designated J) on the lower shelf of
figure 1. Mark and drill
three 7/6-inch holes
work table (E) as shown in figure 2. Secure the kits
through the table top aligned with the mounting
to the shelves with fabricated webbing straps as
holes in the base of the stand. Secure the drill and
required.
stand with three 3/8-24 x 2-1/2-inch hexagon-
head cap screw 5305-26.9-3244, six 25/ 64-inch
4. R e p o r t i n g of Equipment Publications
inside diameter flat washers 5310-167-0804, three
I m p r o v e m e n t s . The reporting of errors,
3 / 8-inch split lockwashers 5310-737-4728, and
omissions and reconmendations for improving this
three 3 / 8-24 hexagon plain nuts 5310-975-2075.
publication by the individual user is encouraged.
e. Generator Set (Figs. 1 and 3). Place the
Reports should be submitted on DA Form 2028
generator set 6115-889-1446 on the floor of the
(Recommended Changes to DA Publications).
van, two inches from the left side of van and flush
Forward completed forms direct to: Commanding
against table (A) as shown in figures 1 and 3.
General, Headquarters, U.S. Army Weapons
Secure the generator to the table legs with webbing
C o m m a n d , ATTN: A M S W E - S M M - P , R o c k
straps which are to be fabricated using webbing
Island, IL 61201.
8305-263-2477 and a buckle 5340-850-8060.
4