TB 9-4940-321-30
(26) Position machinist's vise (5120-00-293-
5.
Installation--Continued
1439) on table top in accordance with figure 23. Using
base of machinist's vise as a template, mark and drill
(22) Position two support angles (11021208) on table top
four 0.56-in. diameter holes through table top. Secure
surface and against the wall in accordance with figure 23
machinist's vise, using four 1/2x 3-in.
hex head
so that the two 0.34-in. diameter holes are on table top.
capscrews (MS90725-119), four 1/2-in. flat washers
Using support angles as templates, mark and drill four
(MS27183-17), four 1/2-in. lockwashers (MS35338-48),
0.34-in. diameter holes through table top and storage
and four 1/2in. hex nuts (MS51967-14).
cabinets. Secure, using four 5/16x 2-1/4-in. hex head
capscrews (MS90725-41), four 5/16-in. flat washers
d. Follow steps (1) thru (4) below for location of
(MS27183-11), four 5/16-in. lockwashers (MS35338-45),
equipment when ISO-2-1 shelter is deployed.
and four 5/16-in. hex nuts (MS51967-5). Secure table
top, with two 20-drawer storage cabinets attached, to
NOTE
rear left wall, using four 60-in.
retaining straps
(7550588-2) (two retaining straps linked together for
Hardware used for steps (1) and (2) is
stored in a drawer of the cabinet
roller assembly.
CAUTION
Be sure storage cabinet drawers
(1) Position work table (4910-00543-7772)
adjacent to hole locations are
against deployed left side wall and aline with floor
mounted blind rivet nuts in accordance with figure 30.
Secure to floor, using six 5/16x 3/4-in. hex head
capscrews (MS90725-32) and six 5/16-in. lockwashers
(23) Position shelf (11021202) between two 20-
(MS3538.845).
drawer storage cabinets; using shelf as a template, mark
and drill four 0.34-in. diameter holes in cabinet sides in
(2) Position two 20-drawer storage cabinets
accordance with figure 27. Secure the shelf, using four
and cabinet roller assembly against rear deployed left
5/16x 3/4-in. hex head capscrews (MS9072532), four
side wall in accordance with figure 30, so that holes in
5/16-in.
flat washers (MS2718311), four 5/16-in.
mounted support angles are aligned with wall mounted
blind rivet nuts in accordance with figure 28. Secure to
(MS519675).
wall, using six 5/16x 7/8-in. hex head capscrews
(24) Position 88-piece die and tap set (5136-
45).
00-357-7504), 82-piece die and tap set (5136-00-357-
7494), 40piece die and tap set (5136-00-3577506), and
(3) Adjust four pad assemblies (11021203-5)
level and plumb (5210-00239-0892) on shelf (11021202)
so they press against floor.
in accordance with figure 27. Secure, using two 60-in.
retaining straps (7550588-2).
(4) Position tool kit' (5180-00699-5273), pinch
bar (5120-00-2241384), a-,d hand reamer set (5110-
(25) Position hand reamer set (5110-00-357-
00357-6858) on deployed floor in accordance with figure
6858) and pinch bar (512000-224-1384) on table top in
accordance with figure 23. Secure, using two 60in.
retaining straps (7550588-2).
21