TB
9-4940-331-30
Installation--Continued
4.
(6) Mark
and drill two 0.25-in.
diameter holes
in right side wall of
t h r o u g h floor.
Secure
cabinets
to
rear
right
side
18-drawer
storage
floor, using eight 3/8- x l-1/8-in.
hex
cabinet
in
accordance
with
head
capscrws
(MS90725-61),
eight
Install
two #10
blind rivet nuts (MS27130-
1 3 / 3 2 - i n . flat washers (MS27183-14),
A20K) .
Position
and secure one strap
eight
3/8-in.
(MS35338-46),
loop
(MS51939-3),
using
two
#10
x
l-in.
and
eight
3/8-in.
hex
nuts
(MS51967-8).
countersunk
head
machine
screws
(MS35190-
275)
(3)
Position
two
18-drawer
storage
cabinets
(7)
Mark
and
drill
two
0.22-in.
against right side
wall in accordance
diameter
holes
in
right
side
rear
truck
3. Using the holes
slats in accordance
with
in
the
cabinet
bottoms
as
templates,
Position
and
secure
one
strap
loop
mark
and
drill
eight
0.41-in.
diameter
(MS51939-3),
using
two
#10
x
l-in.
holes
through
floor.
Secure
cabinets
c o u n t e r s u n k head machine
screws
(MS35190-
to
floor,
using
eight
3/8-
x
l-1/8-in.
275),
two
7/32-in.
flat
washers
(MS27183-
hex
head
capscrews
(MS90725-61),
eight
42),
two
#10
(MS35338-43),
13/32-in.
flat
washers
(MS27183-14),
and
two
#10
hex
nuts
(MS35649-202)
eight
3/8-in.
(MS35338-46),
and
eight
3/8-in.
hex
nuts
(MS51967-8).
(8)
Position
one
vehicle
boarding
ladder
(2540-00-641-0187)
against
rear
(4)
Position
three
18-drawer
1 8 - d r a w e r storage cabinet in accordance
storage
cabinets
and
one
42-drawer
storage
cabinet
(7125-00-
66-in.
retaining
strap
(7550588-9).
335-0292)
against
the
left
side
wall
in
accordance
with
and
4.
Using
b.
Follow
steps
(1)
thru
(14)
below
the
holes
in
the
cabinet
bottoms
as
for
electrical
component
installation.
templates, mark and drill sixteen 0.41-
in. diameter holes (four per cabinet
(1)
To
provide
sufficient
head
bottom)
through
floor.
Secure
cabinets
room
for
personnel to
work in the M35A2
to floor, using sixteen
3/8- x l-l/8-
cargo truck, raise the
bows 18 inches
in.
hex
head
capscrews
(MS90725-61),
and drill ten 0.44-in.
diameter holes
sixteen
13/32-in.
flat
washers
(MS27183-
through
bow
sockets
and
bows
in
accord-
14),
ance
with
46),
and sixteen 3/8-in. hex nuts
(MS51967-8).
(2)
Secure
bows
in
place
with
ten
3/8-
x
2-in.
hex
head
capscrews
(MS90725-
(5)
Position
mounting
bracket
of
66),
ten
3/8-in.
(MS35338-
fire
extinguisher
on
46),
and
ten
3/8-in.
hex
nuts
(MS51967-
front
wall
in
accordance
with
8).
and
4.
Mark
and
drill
three
0.22-in.
diameter
holes
through
mounting
bracket.
(3)
Position
switch
box
(Square
D
Using
the
mounting
bracket
as
a
template,
D221NRB) on the
two top truck
slats in
mark
and
drill
three
0.22-in.
diameter
accordance with
9. Using
holes
in
wooden
truck
slats
in
accord-
holes of switch
box as a template, mark
ance
with
7.
Secure
mounting
and drill four
0.12-in. diameter pilot
bracket, using three #10 x l-in. counter-
holes.
Secure switch box to truck
sunk
head
machine
screws
(MS35190-275),
slats
with four #10 x l-in. thread
three
7/32-in.
flat
washers
(MS27183-
forming
screws
(MS51861-49).
42),
three
#10
(MS35338-
43),
and
three
#10
hex
nuts
(MS35649-
202).
Install
fire
extinguisher
in
mounting
bracket.
5