Section I. INTRODUCTION - TB-9-4940-321-300006
Table 1. Mounting Hardware, 280 Shelter - TB-9-4940-321-300007
Table 1. Mounting Hardware, 280 Shelter - TB-9-4940-321-300008
Table 2. Mounting Hardware, ISO-2-1 Shelter - TB-9-4940-321-300009
Table 2. Mounting Hardware, ISO-2-1 Shelter - continued - TB-9-4940-321-300010
Table 2. Mounting Hardware, ISO-2-1 Shelter - continued - TB-9-4940-321-300011
Table 3. Components to be Mounted, 280 Shelter - TB-9-4940-321-300012
Table 4. Components to be Mounted, ISO-2-1 Shelter
Table 4. Components to be Mounted, ISO-2-1 Shelter - continued
Table 5. Electrical Components to be Mounted, 280 Shelter
Table 6. Components to be Fabricated, 280 Shelter
Table 7. Components to be Fabricated, IS0-2-1 Shelter
Section II. INSTALLATION IN 280 SHELTER - TB-9-4940-321-300018
Installation - TB-9-4940-321-300019
Installation - continued - TB-9-4940-321-300020
Installation - continued - TB-9-4940-321-300021
Section III. INSTALLATION IN ISO-2-1 SHELTER - TB-9-4940-321-300022
Installation - TB-9-4940-321-300023
Installation - continued - TB-9-4940-321-300024
Installation - continued - TB-9-4940-321-300025
Installation - continued - TB-9-4940-321-300026
Figure 1. 280 shelter, unit 1. - TB-9-4940-321-300027
Figure 2. Components to be mounted, unit 1, 280, floor plan. - TB-9-4940-321-300028
Figure 3. Dimensions for blind rivet nut installation in floor, unit 1, 280.
Figure 4. Components to be mounted, unit 1, 280, right side elevation. - TB-9-4940-321-300030
Figure 5. Components to be mounted, unit 1, 280, left side elevation.
Figure 6. Location of relocated components of modified front panel assembly, unit 1, 280.
Figure 7. Blind rivet nut installation in front end wall, unit 1, 280.
Figure 8. Blind rivet nut installation in door end wall, unit 1, 280.
Figure 9. Shelf support and table support angle installation on door end wall, unit 1, 280.
Figure 10. Components to be mounted, door and front end elevations, unit 1, 280.
Figure 11. Eyebolt installation, unit 1, 280.
Figure 12. Dimensions for lathe mounting plate, 7551819, unit 1, 280.
Figure 13. Dimensions for right and left wall angles, 7551820 and 7551821, unit 1, 280.
Figure 14. Dimensions for left and right braces, 7551822 and 7551823, unit 1, 280.
Figure 15. Dimensions for right side and left side table tops, 7551824 and 7551825, unit 1, 280.
Figure 16. Dimensions for right side and left side table support angles, 7551826 and 7551827, unit 1, 280.
Figure 17. Dimensions for rear right side and front right side bench supports, 7551828 and 7551830, unit 1, 280.
Figure 18. Dimensions for rear left side and front left side bench supports, 7551829 and 7551831, unit 1, 280.
Figure 19. Dimensions for shelf, 7551832, unit 1, 280.
Figure 20. Dimensions for shelf support, 7551834, unit 1, 280.
Figure 21. Strap loop location for MGDS attachment, unit 1, 280.
Figure 22. ISO-2-1 shelter, unit 2.
Figure 23. Components to be mounted, unit 2, ISO-2-1, floor plan.
Figure 24. Dimensions for blind rivet nut installation in floor, unit 2, ISO-2-1.
Figure 25. Components to be mounted, unit 2, ISO-2-1, right side elevation.
Figure 26. Dimensions for blind rivet nut installation in right side wall, unit 2, ISO-2-1.
Figure 27. Components to be mounted, unit 2, ISO-2-1, left side elevation.
Figure 28. Dimensions for blind rivet nut installation in left side wall, unit 2, ISO-2-1.
unit 2, ISO-2-1.
Figure 30. Location of blind rivet nuts and components, deployed floor, unit 2, ISO-2-1.
Figure 31. Dimensions for lathe mounting plate, 11021199, unit 2, ISO-2-1.
Figure 32. Dimensions for table top, 11021200, unit 2, ISO-2-1.
Figure 33. Dimensions for shelf, 11021201, unit 2, IS0-2-1.
Figure 34. Dimensions for shelf, 11021202, unit 2, ISO-2-1.
Figure 35. Dimensions for support angle, 11021208, unit 2, IS0-2-1.
Figure 36. Dimensions for cabinet roller assembly, 11021203, unit 2, ISO-2-1.
Figure 37. Dimensions for angles, 11021203-2 and 11021203-3, unit 2, ISO-2-1.
Figure 38. Dimensions for angle, gusset, and spacer, 11021203-1, 11021203-4, and 11021203-6, unit 2, ISO-2-1.
Figure 39. Dimensions for pad assembly, 11021203-5, unit 2, ISO-2-1.
Figure 40. Dimensions for wheel, axle, and bearing, 11021204, 11021205, and 11021214, unit 2, IS0-2-1.
Figure 41. Dimensions for insert, 11021215, unit 2, ISO-2-1.
Figure 42. Location of power distribution panel, unit 1, 280.
Figure 43. Electrical installation, unit 1, 280.
Figure 44. Wiring diagram, 7551836, unit 1, 280.
Figure 45. Dimensions for flexible cord, unit 1, 280.
Figure 46. Flexible cord installation, unit 1, 280.
Table 8. Standard Conversion Chart
TB-9-4940-321-30 Machine Shop Organizational Maintenance (NSN 4940-00-209-6238) Installation In One Maintenance Shelter (NSN 4940-00-919-8409) Manual
Table 1. Mounting Hardware, 280 Shelter - TB-9-4940-321-300007
Table 1. Mounting Hardware, 280 Shelter - TB-9-4940-321-300008
Table 2. Mounting Hardware, ISO-2-1 Shelter - TB-9-4940-321-300009
Table 2. Mounting Hardware, ISO-2-1 Shelter - continued - TB-9-4940-321-300010
Table 2. Mounting Hardware, ISO-2-1 Shelter - continued - TB-9-4940-321-300011
Table 3. Components to be Mounted, 280 Shelter - TB-9-4940-321-300012
Table 4. Components to be Mounted, ISO-2-1 Shelter
Table 4. Components to be Mounted, ISO-2-1 Shelter - continued
Table 5. Electrical Components to be Mounted, 280 Shelter
Table 6. Components to be Fabricated, 280 Shelter
Table 7. Components to be Fabricated, IS0-2-1 Shelter
Section II. INSTALLATION IN 280 SHELTER - TB-9-4940-321-300018
Installation - TB-9-4940-321-300019
Installation - continued - TB-9-4940-321-300020
Installation - continued - TB-9-4940-321-300021
Section III. INSTALLATION IN ISO-2-1 SHELTER - TB-9-4940-321-300022
Installation - TB-9-4940-321-300023
Installation - continued - TB-9-4940-321-300024
Installation - continued - TB-9-4940-321-300025
Installation - continued - TB-9-4940-321-300026
Figure 1. 280 shelter, unit 1. - TB-9-4940-321-300027
Figure 2. Components to be mounted, unit 1, 280, floor plan. - TB-9-4940-321-300028
Figure 3. Dimensions for blind rivet nut installation in floor, unit 1, 280.
Figure 4. Components to be mounted, unit 1, 280, right side elevation. - TB-9-4940-321-300030
Figure 5. Components to be mounted, unit 1, 280, left side elevation.
Figure 6. Location of relocated components of modified front panel assembly, unit 1, 280.
Figure 7. Blind rivet nut installation in front end wall, unit 1, 280.
Figure 8. Blind rivet nut installation in door end wall, unit 1, 280.
Figure 9. Shelf support and table support angle installation on door end wall, unit 1, 280.
Figure 10. Components to be mounted, door and front end elevations, unit 1, 280.
Figure 11. Eyebolt installation, unit 1, 280.
Figure 12. Dimensions for lathe mounting plate, 7551819, unit 1, 280.
Figure 13. Dimensions for right and left wall angles, 7551820 and 7551821, unit 1, 280.
Figure 14. Dimensions for left and right braces, 7551822 and 7551823, unit 1, 280.
Figure 15. Dimensions for right side and left side table tops, 7551824 and 7551825, unit 1, 280.
Figure 16. Dimensions for right side and left side table support angles, 7551826 and 7551827, unit 1, 280.
Figure 17. Dimensions for rear right side and front right side bench supports, 7551828 and 7551830, unit 1, 280.
Figure 18. Dimensions for rear left side and front left side bench supports, 7551829 and 7551831, unit 1, 280.
Figure 19. Dimensions for shelf, 7551832, unit 1, 280.
Figure 20. Dimensions for shelf support, 7551834, unit 1, 280.
Figure 21. Strap loop location for MGDS attachment, unit 1, 280.
Figure 22. ISO-2-1 shelter, unit 2.
Figure 23. Components to be mounted, unit 2, ISO-2-1, floor plan.
Figure 24. Dimensions for blind rivet nut installation in floor, unit 2, ISO-2-1.
Figure 25. Components to be mounted, unit 2, ISO-2-1, right side elevation.
Figure 26. Dimensions for blind rivet nut installation in right side wall, unit 2, ISO-2-1.
Figure 27. Components to be mounted, unit 2, ISO-2-1, left side elevation.
Figure 28. Dimensions for blind rivet nut installation in left side wall, unit 2, ISO-2-1.
unit 2, ISO-2-1.
Figure 30. Location of blind rivet nuts and components, deployed floor, unit 2, ISO-2-1.
Figure 31. Dimensions for lathe mounting plate, 11021199, unit 2, ISO-2-1.
Figure 32. Dimensions for table top, 11021200, unit 2, ISO-2-1.
Figure 33. Dimensions for shelf, 11021201, unit 2, IS0-2-1.
Figure 34. Dimensions for shelf, 11021202, unit 2, ISO-2-1.
Figure 35. Dimensions for support angle, 11021208, unit 2, IS0-2-1.
Figure 36. Dimensions for cabinet roller assembly, 11021203, unit 2, ISO-2-1.
Figure 37. Dimensions for angles, 11021203-2 and 11021203-3, unit 2, ISO-2-1.
Figure 38. Dimensions for angle, gusset, and spacer, 11021203-1, 11021203-4, and 11021203-6, unit 2, ISO-2-1.
Figure 39. Dimensions for pad assembly, 11021203-5, unit 2, ISO-2-1.
Figure 40. Dimensions for wheel, axle, and bearing, 11021204, 11021205, and 11021214, unit 2, IS0-2-1.
Figure 41. Dimensions for insert, 11021215, unit 2, ISO-2-1.
Figure 42. Location of power distribution panel, unit 1, 280.
Figure 43. Electrical installation, unit 1, 280.
Figure 44. Wiring diagram, 7551836, unit 1, 280.
Figure 45. Dimensions for flexible cord, unit 1, 280.
Figure 46. Flexible cord installation, unit 1, 280.
Table 8. Standard Conversion Chart
TB-9-4940-321-30 Machine Shop Organizational Maintenance (NSN 4940-00-209-6238) Installation In One Maintenance Shelter (NSN 4940-00-919-8409) Manual
