Chapter 1. INTRODUCTION - TM-5-4940-225-340005
Tabulated Data - TM-5-4940-225-340006
Table 1-1. Air Compressor Repair and Replacement Standards
Table 1-1. Air Compressor Repair and Replacement Standard
Chapter 2. GENERAL MAINTENANCE INSTRUCTIONS - TM-5-4940-225-340009
Table 2-I. Troubleshooting
Figure 2-1. Interface suppression components, removal and installation (Sheet 1 of 2).
Section IV. REMOVAL AND INSTALLATION OF MAJOR COMPONENTS
Figure 2-2. Dynamotor-welder, removal and installation.
Figure 2-3. Control cubicle, removal and installation
Figure 2-4. Van body, removal and installation.
Chapter 3. REPAIR INSTRUCTIONS
Figure 3-1. Air compressor, disassembly and reassembly (sheet 1 of 4).
Figure 3-1. Air compressor, disassembly and reassembly (sheet 2 of 4).
Figure 3-1. Air compressor, disassembly and reassembly (sheet 3 of 4).
Figure 3-1. Air compressor, disassembly and reassembly (sheet 4 of 4).
Figure 3-2. .4ir compressor drive rnotor, disassembly and reassembly.
Section II. DYNAMOTOR-WELDER
Figure 3-4. Overspeed linkage. removal and installation. (Model SEORL Only/
Figure 3-5. Overspeed safety switch, Adjustment.
Figure 3-6. Ovwespeed safety switch. disassembly and reassembly.
Figure 3-7. Governor, removal and installation.
Drive Belts and Shock Absorber
Figure 3-9. Drive sheave, removal and installation.
Figure 3-11. Dynamotor armature, removal and installation.
Field Coils, Pole Shoes, Brush Holders, and Mounting Rings
Figure 3-13, Dynamotor-welder frames, field coils, pole shoes, brush holders, and mounting rings, removal and installation, disassembly and reassembly (sheet 1 of 3).
Figure 3-13, Dynamotor-welder frames, field coils, pole shoes, brush holders, and mounting rings, removal and installation, disassembly and reassembly (sheet 2 of 3).
Figure 3-13, Dynamotor-welder frames, field coils, pole shoes, brush holders, and mounting rings, removal and installation, disassembly and reassembly (sheet 3 of 3).
Figure 3-14. Rotary switch (10 Range), Disassembly and Reassembly
Generator Output Contactor
Figure 3-16. Genaertor output contractor, disassembly and reassembly
Overload Switch
Figure 3-18. Resistor and relay mounting panel, and emergency power panel disassembly and reassembly
Exciter Booster
Wiring (control cubicle)
Dynamotor Switch
Running Time Meter
Side Lifting Cylinder and Hydraulic
Side Lifting Hydraulic Pump
Figure 3-21. Hydraulic pump, disassembly and reassembly.
Figure 3-22. Personnel heater, removal and installation.
Figure 3-23. Lathe and lathe table. removal and installation.
Appendix A. REFERENCES - TM-5-4940-225-340049
INDEX - TM-5-4940-225-340051
Figure 1-1. Schematic Wiring Diagram (dynamotor welder)
Figure 1-2. Schematic wiring diagram (dynamotor welder)
Distribution - TM-5-4940-225-340055
TM-5-4940-225-34 Shop Equipment Organizational Repair Truck Mounted (Southwest Truck Body Model Seorl) FSN 4940-169-3041 Manual
Tabulated Data - TM-5-4940-225-340006
Table 1-1. Air Compressor Repair and Replacement Standards
Table 1-1. Air Compressor Repair and Replacement Standard
Chapter 2. GENERAL MAINTENANCE INSTRUCTIONS - TM-5-4940-225-340009
Table 2-I. Troubleshooting
Figure 2-1. Interface suppression components, removal and installation (Sheet 1 of 2).
Section IV. REMOVAL AND INSTALLATION OF MAJOR COMPONENTS
Figure 2-2. Dynamotor-welder, removal and installation.
Figure 2-3. Control cubicle, removal and installation
Figure 2-4. Van body, removal and installation.
Chapter 3. REPAIR INSTRUCTIONS
Figure 3-1. Air compressor, disassembly and reassembly (sheet 1 of 4).
Figure 3-1. Air compressor, disassembly and reassembly (sheet 2 of 4).
Figure 3-1. Air compressor, disassembly and reassembly (sheet 3 of 4).
Figure 3-1. Air compressor, disassembly and reassembly (sheet 4 of 4).
Figure 3-2. .4ir compressor drive rnotor, disassembly and reassembly.
Section II. DYNAMOTOR-WELDER
Figure 3-4. Overspeed linkage. removal and installation. (Model SEORL Only/
Figure 3-5. Overspeed safety switch, Adjustment.
Figure 3-6. Ovwespeed safety switch. disassembly and reassembly.
Figure 3-7. Governor, removal and installation.
Drive Belts and Shock Absorber
Figure 3-9. Drive sheave, removal and installation.
Figure 3-11. Dynamotor armature, removal and installation.
Field Coils, Pole Shoes, Brush Holders, and Mounting Rings
Figure 3-13, Dynamotor-welder frames, field coils, pole shoes, brush holders, and mounting rings, removal and installation, disassembly and reassembly (sheet 1 of 3).
Figure 3-13, Dynamotor-welder frames, field coils, pole shoes, brush holders, and mounting rings, removal and installation, disassembly and reassembly (sheet 2 of 3).
Figure 3-13, Dynamotor-welder frames, field coils, pole shoes, brush holders, and mounting rings, removal and installation, disassembly and reassembly (sheet 3 of 3).
Figure 3-14. Rotary switch (10 Range), Disassembly and Reassembly
Generator Output Contactor
Figure 3-16. Genaertor output contractor, disassembly and reassembly
Overload Switch
Figure 3-18. Resistor and relay mounting panel, and emergency power panel disassembly and reassembly
Exciter Booster
Wiring (control cubicle)
Dynamotor Switch
Running Time Meter
Side Lifting Cylinder and Hydraulic
Side Lifting Hydraulic Pump
Figure 3-21. Hydraulic pump, disassembly and reassembly.
Figure 3-22. Personnel heater, removal and installation.
Figure 3-23. Lathe and lathe table. removal and installation.
Appendix A. REFERENCES - TM-5-4940-225-340049
INDEX - TM-5-4940-225-340051
Figure 1-1. Schematic Wiring Diagram (dynamotor welder)
Figure 1-2. Schematic wiring diagram (dynamotor welder)
Distribution - TM-5-4940-225-340055
TM-5-4940-225-34 Shop Equipment Organizational Repair Truck Mounted (Southwest Truck Body Model Seorl) FSN 4940-169-3041 Manual
