TB 9-3470-201-30
4.
Installation--Continued
25-ft extension lights (6230-00-729-
9259) on the middle set of squareneck
holes through the storage cabinet wall.
bolts located on the opposite side of
Fasten plate to storage cabinet wall
storage cabinet group in accordance
using the two screws and nuts that were
with figure 1.
previously removed. Using the in-
stalled plate as a template, drill one
(18) Install two 50-ft electrical
0.41-in. diameter hole through the
power cable assemblies (6150-00-682-
storage cabinet wall. Also, mark and
3460) on the remaining two pairs of
drill one 0.41-in. diameter hole
squareneck bolts, one 50-ft electrical
through the lower storage cabinet wall
power cable assembly for each pair of
in accordance with figure 3.
squareneck bolts. Secure the cable
assemblies and extension lights in-
NOTE
stalled in steps 16 and 17 with one 48-
Repeat step 14 three times
in. retaining strap (7550588-3).
for the other side of the
storage cabinet group.
(19) Position upright drilling
Refer to figure 3.
machine (3413-00-964-9379) on semi-
trailer floor in accordance with
(15) Assemble one 3/8- x 5-1/2-in.
squareneck bolt (MS35751-84) with one
upright drilling machine as a template,
3/8-in. hex nut (MS51967-8), one
mark and drill four 0.41-in. diameter
13/32-in. flat washer (MS27183-14), and
holes through the floor. Secure upright
one 3/8-in. lockwasher (MS35338-46).
drilling machine to floor using four
Place the squareneck bolt with assem-
3/8- x 2-1/4-in. hex head capscrews
bled parts through the 0.41-in. diam-
(MS90725-67) and four 13/32-in. flat
eter hole in plate atttached to upper
washers (MS27183-14); under the floor
storage cabinet wall and fasten to the
use four 3/8-in. flat washers (AN970-
wall using one 3/8-in. hex nut (MS51967-
6), four 3/8-in. lockwashers (MS35338-
8). Install another 3/8- x 5-1/2-in.
46), and four 3/8-in. hex nuts (MS51967-
squareneck bolt with the same assembled
8).
parts in the 0.41-in. diameter hole in
the lower storage cabinet wall follow-
(20) Machine table vise (3460-00-
ing the same procedure.
277-3504) is to be attached to the
upright drilling machine table with the
NOTE
T-bolts provided with the machine table
Repeat step 15 three times
for the other side of the
storage cabinet group.
Refer to figure 3.
(16) Wrap one 50-ft electrical
power cable assembly (6150-00-682-3460)
line engine generator set as a template,
around two squareneck bolts on the
mark and drill four 0.66-in. diameter
storage cabinet wall in accordance with
holes through the floor. Secure gaso-
figure 1. Secure 50-ft electrical
line engine generator set using four
power cable assembly with one 24-in.
5/8- x 2-1/2-in. hex head capscrews
retaining strap (7550588-5).
(MS90725-166) and four 21/32-in. flat
washers (MS27183-21); under the floor
use four 5/8-in. flat washers (AN970-
(17) Install one 25-ft electrical
10), four 5/8-in, lockwashers (MS35338-
power cable assembly (4910-00-725-
50), and four 5/8-in. hex nuts (MS51967-
9558), one 7-ft electrical power cable
20).
assembly (4910-00-800-1405), and two
11
