TB 9-4940-319-30
5.
Installation - Continued
table to floor, using two 5/16- x 1-in. machine bolts
(6) Position anvil block, with attached
(MS90725-34) installed in front end of work table, four
support angles, next to welding table in accordance with
5/16- x 3/4-in. machine bolts (MS90725-32), and six
5/16-in. lockwashers (MS35338-45).
floor-mounted blind rivet nuts in accordance with figure
(3) Position welding table (3436-00-847-
head capscrews (MS90725-60), two 3/8- x 1-1/4-in. hex
3772) against middle right wall in accordance with figures
head capscrews (MS90725-62) installed in front set of
blind rivet nuts, and six 3/8-in. lockwashers (MS35338-
through welding table legs. Position over installed floor-
46).
mounted blind rivet nuts in accordance with figure 8.
Secure welding table to floor, using four 3/8-xl-1/8-in. hex
(7) Position blacksmith's anvil (5120-00-
head capscrews (MS90725-61) and four 3/8-in.
180-2885) on top of anvil block in accordance with
Lockwashers (MS35338-46).
and drill two 0.22-in. diameter pilot holes in top of anvil
block. Secure blacksmith's anvil to anvil block, using two
NOTE
5/16- x 2-1/2-in. lag screws (MS16992-525) and two
The two blind rivet nuts (S37B285)
5/16-in. lockwashers (MS35338-45).
installed in front of welding table are
used to secure welding table when
(8) Position mounting bracket of fire
ISO-2-1 shelter is in the deployed
extinguisher (4210-00-555-8837) on left front wall in
position.
accordance with figure 11. Mark and drill three 0.22-in.
diameter holes in mounting bracket. Position over
(4) Position band saw (3405-00-517-
installed wall-mounted blind rivet nuts in accordance with
0592) against rear left wall in accordance with figures 7
and 11. Mark and drill four 0.41-in. diameter holes
#10 x 1/2-in. countersunk head machine screws
through band saw legs. Position over installed floor-
(MS35190-271). Install fire extinguisher in bracket (fig.
mounted blind rivet nuts in accordance with figure 8.
Secure band saw to floor, using two 3/8- x 7/8-in. hex
head capscrews (MS90725-59) installed in rear end of
(9) Remove contents of first aid kit (6545-
band saw, two 3/8 x 1-1/8-in. hex head capscrews
00-922-1200). Mark and drill three 0.22-in. diameter
(MS90725-61), and four 3/8-in. lockwashers (MS35338-
holes in the back of first aid kit. Position first aid kit on
46).
rear left wall and over installed wall-mounted blind rivet
nuts in accordance with figures 11 and 12. Secure first
(5) Position
two
support
angles
aid kit to wall, using three #10 x 1/2-in. countersunk head
(11021151-9) on anvil block (5120-00-449-6644) flush
machine screws (MS35190-271). Install contents of first
with bottom of anvil block in accordance with figure 9.
aid kit.
Using support angles as templates, mark and drill four
0.22-in. diameter pilot holes in bottom of anvil block.
(10) Position oil and water separator (4940-
Secure support angles to anvil block, using four 5/16- x
00-242-4101) on left wall in accordance with figure
1-1/4-in. hex head lag bolts (MS16992-521) and four
5/16-in. lockwashers (MS35338-45).
12
