TB 9-4940-321-30
(14)
Position tool kit (5180-00699-5273) on
4.
Installation--Continued
left side table top (fig. 2). Locate two strap loops
(MS51939-3) 1.00 inch from each end of tool kit and in
in. lockwashers (MS35338-46), and three 3/8-in. hex
line with handles in accordance with figure 2. Using
nuts (MS51967-8).
strap loops as templates, mark and drill four 0.22-in.
diameter holes through left side table top and storage
(10) Secure machine table vise (3460-00-277-
cabinet. Secure strap loops, using four #10 x 1-3/4-in.
3504) to base of upright drilling machine, using furnished
countersunk head machine screws (MS35190278), four
tee bolts and nuts (fig. 2).
#10 flat washers (AN970-3), four #10 lockwashers
(MS35338-43), and four #10 hex nuts (MS35649-202).
(11) Position utility grinding machine (3415-00-
Secure tool kit, using two 24-in. retaining straps
517-7754) on right side table top in accordance with
(7550588-5) (fig. 5).
template, mark and drill three 0.34-in. diameter holes
(15) Position level and plumb (5120-00-239-
through right side table top and storage cabinet. Secure
0892) on top of pipe threading set (5180-00-357-7514)
utility grinding machine, using three 5/16x 2-in. hex head
and place on top shelf in accordance with figure 4.
capscrews (MS90725-40), three 5/16-in. lockwashers
Secure with two 48-in. retaining straps (7550588-3).
(MS35338-45), and three 5/16-in. hex nuts (MS51967-
5).
(16) Position 88-piece die and tap set (5136-
00-357-7504) on lower shelf on right side of 280 shelter
(12) Position hand reamer set (5110-00-357-
in accordance with figure 4.
Secure with two 48-in.
6858) on right rear corner of right side table top
retaining straps (75505883).
using two 48-in. retaining straps (7550588-3) wrapped
(17) Place safety can (7240-00222-3084) in
around hand reamer set and right side table top.
wash pan (4940-00-7953595) and position on shelf
(7551832) in accordance with figure 5. Secure with two
NOTE
48-in. retaining straps (75505883). (Pass one retaining
When installing machinist's vise,
strap through handle of safety can.)
install capscrews from underside
with flat washers on both top and
(18) Coil cords of two extension lights (6230-
bottom
and
hex
nuts
and
00-729-9259) around hooks on left side of front panel
lockwashers on top.
assembly. Coil two power cable assemblies (615000-
682-3460) on right side of front panel assembly in
(13) Position machinist's vise (5120-00-293-
accordance with figure 10. Secure with two 24-in.
1439) on left side table top (7551825) in accordance with
retaining straps (7550588-5).
mark and drill four 0.56-in. diameter holes through left
(19) Reassemble ground rod, hanger, and
side table top and storage cabinet. Secure machinist's
bracket (previously removed from front panel assembly)
vise to left side table top, using four x 3-in. hex head
on the right rear wall as shown in figure 10, using
capscrews (MS90725-119), eight 17/32-in. flat washers
(MS27183-18), four 1/2-in. lockwashers (MS35338-48),
and four 1/2in. hex nuts (MS51967-14).
15
