4910-543-7772 installed on the right side of the
van. Place the other table against the left wall
shop van. Locate the vise 6 inches from the
and 1 inch from the front wall of the van. Aline
right end and inch from the front edge of the
the two holes in the back of the table top with two
table. Place the other vise on work table 4910-
holes in the steel angle on the shop van wall by
543-7771 on the left side of the shop-van. Locate
shifting the work table as required. Mark, and
the vise 18 inches from the right end of the table
drill six 3/8-inch holes through the van floor for
and inch from the front edge. Mark, and drill
each table. Secure each table to the floor with
three inch holes through the table top for each
two 5/16-18 by 1 1/4-inch hexagon-head machine
vise. Secure each vise to the table with three
bolts 5306-012-2027 (for wheel plates), four 5/16-18
-13 by 3-inch square-neck bolts 5306-010-9141,
by 2-inch hexagon-head machine bolts 5306-208-
three 17/122-inch inside diameter flat washers 5310-
1559, six 7/16-inch inside diameter rectangular flat
197-3316 three -inch split Lockwashers 5310-
washers 5310-209-061, six 11/22-inch inside diam-
012-0384,' and three -13 hexagon plain nuts
eter flat washers 5310-050-2246, six 5/16G-inch split
5310-010-2637.
agon plain nuts 5310-639-7046. Secure each table
d. Utility Grinding Machine (fig. 1). Place the
top to the steel angle (factory installed on van
utility grinding machine 3415-5177754 on work
wall) with two 5/8-11 by 3 1/4-inch hexagon-head cap-
table 4910-543-7771 installed on the right side of
screws 5305-022-3518, two 21/22-inch inside diam-
the shop-van. Locate the grinding machine
eter flat washers 5310-753-8683, and two 5/8-inch
32 inches from the left end and 1 inch-from the
split lockwashers 5310-010-3331.
front edge of the table as shown in figure 1. Mark,
and drill two 5/16-inch holes through the table top.
Note. The 5/8-11 capscrews thread into nuts that arc
factory installed in the table top.
Secure the grinding machine to the table with two
5/16-18 by 3-inch square-neck bolts 5306-010-
9108, two 11/32-inch inside diameter flat washers
are two work tables 4910-543-7772 to be installed
5310-050-2246, two 5/16-inch split lockwashers
iln the rear of the shop-van. Place one work
5310-012-0214, and two 5/16-18 square plain nuts
table against the right wall of the van and flush
5310-010-5605.
against the end of work table 4910-543-7771.
e. Portable Electric Drill w/Stand (fig. 1). Place
Place the other work table against the left wall
the portable electric drill (with stand) 5130-473-
of the van and flush against the end of the other
work table 49105437771; Aline the two holes
6224 on work table 4910-543-7772 inatalled on
in the back of the table top with two holes in the
the left side of the shop-van. Locate the drill 36
steel angle on the shop-van wall by shifting the
inches from the left end and 2 inches from the front
work table as required. Mark, and drill six 3/8-
edge of the table. Mark, and drill four 3/8-inch
inch holes through the van floor for each table.
holes through the table top. Secure the drill
Secure each table to the floor with four 5/16-18 by
to the table with four 3/8-16 by 4-inch square-neck
1 1/4-inch hexagon-head machine bolts 5306-012-
bolts 5306-010-9120, four 12/32-inch inside diam-
2027 (for wheel plates), two 5/16-18 by 2-inch
eter flat washers 5310582-5977, four 3/8-inch split
hexagon-head machine bolts 5306-208-1559, six
%c-inch inside diameter rectangular flat washers
plain nuts 5310-010-5606.
5310-209-0061, six 11/32-inch inside diameter flat
f. Generator Set (fig. 1). Place the generator
washers 5310-050-2246, six 5/16-inch split lock-
set 6115-245-2522 on the floor of the van against
washers 5310-012-0214, and six 5/16-18 hexagon
the front wall and the right front table. Secure
plain nuts 5310-39-7046. Secure each table
the generator to the table legs with two 28-inch
top to the steel angle (factory installed on van
web straps 5340-543-7110 by passing the straps
wall) with two %-11 by 3 1/4-inch hexagon-head cap
through the carrying handles on the generator and
screws 5305-022-3518, two 21/32-inch inside di-
around the table legs.
ameter flat washers 5310-753-8683 and two
g. Folding Legged Table (fig. 2). Install the
5/8-inch split lockwashers.
strap fastener loop 5340-339-3770 on the apron of
Note. The 5/8-11 capscrews thread into nuts that are
the folding legged table 7195-357-7480 cantered
factory installed in the table top.
drill two 1/8-inch holes through the apron. Secure
Chinist's vise 5120-293-1439 on work table
the loop to the apron with two No. 10-24 by
TAGO 56SA