TB 9-4910-746-30
(2) Position three storage cab-
4.
Installation--Continued
inets (7125-00-330-0130) in van in
accordance with figures 2, 6, and 7.
(2) Unit 3. Mark and drill
Mark and drill eight 0.34-in. diameter
twelve 0.22-in. diameter holes through
holes in bottom plates of storage
trailer floor in accordance with figure
cabinets (four holes in one storage
16. Secure six strap loops (MS51939-3)
cabinet and two holes per renaining
to trailer floor with twelve #10 x 1-
storage cabinet). Locate at corners,
in. countersunk head machine screws
allowing for minimum required clearance
(MS35190-275), twelve #10 lockwashers
for 5/16-x 1-1/4-in. hex head lag
MS35338-43), and twelve #10 hex nuts
b o l t s . Using storage cabinets as
(MS35649-202) in accordance with figure
tamplates, mark and drill eight 0.22-
15.
in. diameter pilot holes into van floor
1.00 inch deep. Secure storage cabi-
(3) Unit 4. Mark and drill
nets to van floor, using eight 5/16- x
twenty 0.22-in. diameter holes through
1-1/4-in. hex head lag bolts (MS16992-
trailer floor in accordance with figure
521) and eight 5/16-in. lockwashers
19. Secure ten strap loops (MS51939-3)
(MS35338-45).
to trailer floor with twenty #10 x 1-
in. countersunk head machine screws
CAUTION
(MS35190-275), twenty #10 lockwashers
Be sure storage cabinet
(MS35338-43), and twenty #10 hex nuts
(MS35649-202) in accordance with figure
drawers adjacent to hole
18.
locations are removed before
c. Follow steps (1) thru (14) below
for equipment installation in unit 1,
(3) Mark and drill seven 0.44-in.
M109A3 shop van truck.
diameter holes in sides of storage
cabinets in accordance with figures 4
(1) Mark and drill sixteen 0.34-
and 5. Install seven 3/8- x 8-in.
in. diameter holes through horizontal
squareneck bolts (MS35751-89) using
legs of two factory-furnished angle
fourteen 3/8-in. flat washers (MS27183-
13), seven 3/8-in. lockwashers (MS35338-
irons in accordance with figure 2.
46), and fourteen 3/8-in. hex nuts
Position three work tables (4910-00-
(MS51967-8).
357-5342) in accordance with figures 2,
6, and 7 under factory-furnished angle
(4) Install three padlocks (5340-
irons. Using the work tables as tem-
00-682-1508) on storage cabinets in
plates, mark and drill twenty-four
accordance with figure 6.
0.27-in. diameter holes through table
legs and 1.00 inch deep into van floor
(5) Position electrical power
in accordance with figure 3. Reposi-
cable assemblies (two 4910-00-800-1405,
tion work tables and secure to van
two 4910-00-725-9558, and three 6150-
floor using twenty-four 3/8- x 1-1/4-
in. hex head lag bolts (MS16992-540)
00-682-3460) and special purpose cable
kit (2590-00-148-7961) on cabinet
and twenty-four 3/8-in. lockwashers
(MS35338-46). Using the drilled angle
squareneck bolts in accordance with
figures 2 and 6.
irons as templates, mark and drill
sixteen 0.34-in. diameter holes through
CAUTION
tabletops in accordance with figure 2.
Be sure storage cabinet
Secure work tables to angle iron using
drawers adjacent to hole
sixteen 5/16- x 1-1/8-in. hex head
locations are removed before
capscrews (MS90725-35), sixteen 5/16-
in. flat washers (MS27183-11), sixteen
5/16-in. lockwashers (MS35338-45), and
sixteen 5/16-in. hex nuts (MS51967-5).
9
