TB 9-4910-746-30
4.
Installation--Continued
(11) Position two 115/250 v ac
extension lights (6230-00-268-9436) on
squareneck bolt of storage cabinet in
(6) Mark and drill four 0.25-in.
diameter holes in left side of front
accordance with figures 2 and 6.
wall mounted storage cabinet in accord-
ance with figure 4. Install four #10
(12) Position five wash pans
blind rivet nuts (MS27130-A20) in
(4940-00-795-3595) on table cross
holes. Secure two strap loops (MS51939-
braces in accordance with figure 7 and
3) to storage cabinet using four #10 x
secure in place with a 66.00-in.
1-in. countersunk head machine screws
retaining strap (7550588-9).
(MS35190-275).
(13) Position utility grinding
machine (3415-00-255-2683) on work
(7) Position two 8-ton hydraulic
table in accordance with figures 2 and
jacks (5120-00-595-8396) and 12-ton
7. Using base of utility grinding
hydraulic jack (5120-00-224-7330) in
machine as a template, mark and drill
acccordance with figures 2 and 6.
three 0.38-in. diameter holes through
Secure hydraulic jacks to storage
tabletop. Secure utility grinding
cabinet with a 48.00-in. retaining
machine to tabletop using three 5/16- x
strap (7550588-3).
1-1/2-in. hex head capscres (MS90725-
38), three 5/16-in. flat washers (MS27183-
(8) Position 1-qt liquid measure
11), three 5/16-in. lockwashers (MS35338-
(7240-00-233-6013), 2-qt liquid measure
45), and three 5/16-in. hex nuts (MS51967-
(7240-00-225-8113), and 8-qt liquid
5).
measure (7240-00-255-5996) in van as
shown in figure 2. Secure liquid
(14) Ladder (2540-00-641-0187) is
measures to van wall with a 66.00-in.
stowed in frame of van in accordance
retaining strap (7550588-9) in accord-
with figure 2.
ance with figures 2 and 6.
d. Follow steps (1) thru (18) below
(9) Position 4-in. machinist's
for equipment installation in unit 2,
vise (5120-00-293-1439) on work table
M35A2 cargo truck.
right side in van as shown in figures
(1) Position four work tables
ist's vise as a template, mark and
(4910-00-357-5342) in truck in accord-
drill four O.56-in. diameter holes in
ance with figure 9. Using work tables
tabletop. Secure 4-in. machinist's
as templates, mark and drill thirty-two
vise to work table with four 1/2- x 2-
0.44-in. diameter holes through table
in. hex head capscrews (MS90725-115),
legs and truck floor in accordance with
four 1/2-in. flat washers (MS27183-17),
four 1/2-in. lockwashers (MS35338-48),
floor using thirty-two 3/8- x 1-1/8-in.
and four 1/2-in. hex nuts (MS51967-14).
hex head capscrews (MS90725-61),
thirty-two 3/8-in. flat washers (MS27183-
(10) Position 6-in. machinist's
13), thirty-two 3/8-in. lockwashers
vise (5120-00-223-1945) on work table
(MS35338-46), and thirty-two 3/8-in.
left side in van as shown in figures 2
hex nuts (MS51967-8).
and 7. Using the base of the machin-
ist's vise as a template, mark and
CAUTION
drill four O.56-in. diameter holes
Be sure storage cabinet
through tabletop. Secure machinist's
drawers adjacent to hole
vise to tabletop with four 1/2- x 2-in.
locations are removed before
hex head capscrews (MS90725-115), four
1/2-in. flat washers (MS27183-17), four
1/2-in. lockwashers (MS35338-48), and
four 1/2-in. hex nuts (MS51967-14).
10
