(1) Raise each bow 18 inches from the bottom
(4) Attach the chain of the chain leg assembly
of their sockets.
to the truck rack to avoid loss.
(2) Clamp (or hold ) the bow in this position
(5) Secure the paulin extension to the existing
and drill a 7 / 16 inch hole through the bow and the
truck cover.
bow socket.
c. Table 1 contains materials for extending the
bows and the necessary paulin extension.
(3) Secure the bow in this position by inserting
chain leg assembly through the bow socket and
bow.
Nomenclature
Use
FSN
Bow and bow socket extension,
CHAIN ASSEMBLY, SINGLE
4910-526-7689
LEG :
(10 required)
2540-449-7180
PAULIN, EXTENSION SET:
Attachment to truck canvas top.
truck side extension, set of 4.
3. Electrical Wiring and Equipment (Fig. 1).
receptacle, and joining cables in parallel with the
white wire (neutral) being connected to the bright
a. The electrical wiring will be installed as
or shell connection of the lighting fixtures. Ground
follows :
the green conductor under the head of one of the
(1) Install two electrical box connectors 5975-
mounting screws in each junction box. Install
152-1142 in each of the three junction boxes 5975-
junction box cover 5975-284-6284 to the electrical
194-8862. Secure the junction boxes to the under
receptacle connector.
side and centered on the second, third, and fourth
bows from the front with six No. 10-5/8-inch round-
(6) Strip 5 inches of the top insulation from
each end of a 38 foot length of power cable 6145-
head wood screws 5305-014-9921.
643-0012. Strip off 1/2-inch of insulation and install
(2) Install one electrical box connector 5975-.
a terminal lug 5940-050-6214 on one end of each
152-1142 in junction box 5975-194-8878. Secure
conductor. Insert this end of the power cable into
this junction box to the inner side of the top slat at
the in-put end of the circuit breaker. Connect both
the rear of the right side rack with two No. 10-5/8-
green conductors to the ground terminal. Connect
inch round-head wood screws 5305-014-9921.
the other two conductors to the in-put terminals,
(3) Install two electrical box connectors 5975-
maintaining color continuity so that neutral
152-1142 in the circuit breaker 5925-283-2217.
conductor is essentially continuous from the source
Secure the circuit breaker to the underside and
of power. Strip off 1/2-inch of insulation from the
centered on the rear bow with four No. 10-5/8-inch
green conductor on the other end of the power cable
round-head wood screws 5305-014-9921.
and attach a terminal lug 5940-050-6214. Cut the
(4) Strip 5 inches of the top insulation from
remaining conductors back to the required length
one end of a 24 foot length of power cable 6145-
and attach the electrical plug connector 5935-280-
643-0012. Strip off 1/2-inch of insulation and
2383. The green wire is to be connected to the
install a terminal lug 5940-050-6214 on each
grounding terminal, the white or neutral wire is to
conductor. Insert this end into the out-put end of
be connected to the bright or identified neutral
the circuit breaker. From the green conductors to
terminal and the black wire is to be connected to
meet the ground terminal and connect the other two
the remaining terminal. Coil the cable and secure
conductors to the out-put terminals. Thread the
the coil to the top of the rear bow with a strap
other end of the power cable through the three
fabricated with webbing 8305-263-2477 and a
junction boxes mounted in the top and down to the
buckle 5340-850-8060. Secure the cables to the
junction box mounted on the top slat at the rear of
bows and side rack with eight retaining straps
the right side rack.
5340-598-2476 and eight No. 10-5/8-inch round.
(5) Connect and install a lighting fixture 6210-
head wood crews 5305-014-9921.
299-699 in each of three top junction boxes.
b. Figure 1 shows the installation of the electrical
Connect and install the electrical receptacle con-
wiring and equipment in the cargo truck. Table 2
nector 5935-577-0283 in the juction box mounted
contains the materials required for wiring the truck.
on the inner side of the top slat at the rear of the
right side rack. Connect the lighting fixtures,
