TB 9-4910-745-30
3.
Installation--Continued
3. Refer to figure 3 for mounting
dimensions. Mark and drill eight 0.37-
c. Unit 1. Follow steps 1 thru 25
in. diameter holes in truck floor.
below; for equipment installation.
Secure the two 1.5-kw generator sets to
truck floor with eight 3/8- x 2-1/2-in.
hex head capscrews (MS90725-68), eight
(1) Position compressor (4310-00-
542-4566) in truck in accordance with
3/8-in. flat washers (MS27183-13),
eight 3/8-in. lockwashers (MS35338-46),
dimensions shown in figures 2 and 3.
Mark and drill four 0.50-in. diameter
and eight 3/8-in. hex nuts (MS51967-8).
holes in truck floor and secure com-
pressor to floor using four 1/2- x 2-
(5) Position oil bucket pump
(4930-00-244-4860), grease bucket pump
in. hex head capscrews (MS90725-115),
four 1/2-in. lockwashers (MS35338-48),
(4930-00-244-4859), and lubricating
and four 1/2-in. hex nuts (MS51967-14).
unit (4930-00-720-4849) in truck as
shown in figure 2. Secure all three
(2) Position 18-drawer storage
components to truck wall with one 110-
in. retaining strap (7550588-10).
cabinet (7125-00-357-5337) in right
front corner of truck and butt one 11-
drawer storage cabinet (7125-00-330-
NOTE
0130) against it in accordance with
Fabricate the 28-in. support
angle as shown in figure 23.
drawers from storage cabinets. Mark
and drill four 0.37-in. diameter holes
(6) Install 28-in. support angle
through storage cabinet bases and truck
(11021151-1) on truck floor in accord-
floor in accordance with figure 3.
ance with figures 2 and 3. Refer to
Secure storage cabinets to truck floor
using four 3/8- x 1-1/8-in. hex head
drill five 0.37-in. diameter holes
capscres (MS90725-61), four 3/8-in.
through 28-in. support angle and truck
floor. Secure 28-in. support angle to
flat washers (MS27183-13), four 3/8-in.
lockwashers (MS35338-46), and four 3/8-
truck floor with five 5/16- x 1-1/4-in.
hex head capscrews (MS90725-35), five
in. hex nuts (MS51967-8).
5/16-in. lockwashers (MS35338-45), and
five 5/16-in. hex nuts (MS51967-5).
(3) Position 3-kw generator set
Position four 12-ton hand hydraulic
(6115-00-017-8239) in truck in accord-
jacks (5120-00-244-7330) between 28-
ance with figures 2 and 3. Refer to
in. support angle (11021151-1) and com-
pressor (4310-00-542-4566) in accord-
and drill four 0.50-in. diameter holes
ance with figure 2.
in truck floor and secure 3-kw gener-
ator set to truck floor with four 1/2-
(7) Position tube-pipe fitting
x 1-1/2-in. hex head capscrews (MS90725-
kit (4730-00-470-6625) on truck floor
113), four 1/2-in. lockwashers (MS35338-
in accordance with figures 2 and 3.
48), and four 1/2-in. hex nuts (MS51967-
Using holes in tube-pipe fitting kit
14).
cabinet base as a template, mark and
drill four 0.25-in. diameter holes.
NOTE
Battery charger (6130-00-
Secure tube-pipe fitting kit to truck
floor with four 1/4- x 1-1/4-in. hex
940-7866) is part of the 3-
head capscrews (MS90725-9), eight 1/4-
kw generator set and does
in. flat washers (MS27183-9), four 1/4-
not require separate instal-
in. lockwashers (MS35338-44), and four
lation.
1/4-in. hex nuts (MS51967-2).
(4) Position the two 1.5-kw
generator sets (6115-00-889-1466) in
truck in accordance with figures 2 and
10
