TB 9-4910-745-30
hex head capscrews (MS90725-88), ten
3.
Installation--Continued
7/16-in. lockwashers (MS35338-47), and
ten 7/16-in. hex nuts (MS51967-11).
(7) Position four 20-ft extension
lights (6230-00-268-9436) and two 25-ft
(2) Position switch box (5930-00-
extension lights (6230-00-729-9259) on
trailer rack in accordance with figure
194-9086) on the two top slats of truck
9 . Secure to top slat on trailer rack
body in accordance with figure 16.
with two 24-in. retaining straps
Using hole of switch box as a template,
(7550588-5).
mark and drill four 0.12-in. diameter
pilot holes. Secure switch box to
truck racks with four 1/4- x 7/8-in.
(8) Position case of impact
wrench set (5120-00-961-9813) on
thread forming screws (MS51861-69).
trailer floor in accordance with figure
(3) Install electrical power
cable assembly (4910-00-800-1405)
with 92-in. retaining strap (7550588-
through box connector in bottom of
7).
switch box and connect to circuit
(9) Position wheel lift truck
breaker inside switch box.
(4910-00-554-5983) in trailer as shown
in figure 9. Move wheel lift truck
(4) Position four lampholder
forward against the box for hydraulic
junction boxes (5975-00-440-2703) on
jack kit (5120-00-595-8388) and secure
inner side of second and fourth bows as
with two 24-in. retaining straps
shown in figure 15. Mark and drill
(7550588-5).
eight 0.12-in. diameter holes and
secure lampholder junction boxes to
(10) Position two acetylene cylin-
bows with eight #10 (0.190) x 7/8-in.
thread forming screws (MS51861-49).
ders (8120-00-268-3360) in trailer as
shown in figure 9. Secure to trailer
(5) Position four duplex junction
wall with 36-in. retaining strap
(7550588-4).
boxes (5975-00-281-0090) on bows as
shown in figures 16 and 17. Mark and
(11) Position eye wash fountain
drill eight 0.12-in. diameter holes and
(4240-00-551-3134) in trailer as shown
secure duplex junction boxes to bows
in figure 9. Secure to trailer wall
with eight #10 (0.190) x 7/8-in. thread
with 30-in. retaining strap (7550588-
forming screws (MS51861-49).
8).
(6) Remove two knockout slugs
(12) Position radiator filling can
from each lampholder junction box
(7240-00-499-8028) in trailer as shown
(5975-00-440-2703) and each duplex
in figure 9 between trailer wall and
junction box (5975-00-281-0090 in line
motor vehicle trestles.
with bows. Install sixteen strain
relief box connectors (5975-00-926-
e. Unit 1. Follow steps 1 thru 13
0590) in the junction boxes and install
below; for electrical component instal-
jam nuts on strain relief box con-
lation.
nectors.
(1) To provide sufficient head
(7) Make up four power cable
room for personnel to work in the M35A2
assemblies (11021163, 11021164, 11021165,
cargo truck, raise the bows 18 inches
11021166) in accordance with figures 19
and drill ten 0.43-in. diameter holes
thru 22 and install in accordance with
through bow sockets and bows. Secure
figures 16, 17, and 18.
bows in place with ten 7/16 x 1-3/8-in.
13
