TB 9-4940-314-30
5. Installation--Continued
storage cabinet wall, using two 3/8-in. flat washers
(AN970-6), 3/8-in. lock- washer (MS35338-46), and two
loops (MS51939-3) to table top, using four #10 x 3/4-in.
3/8-in. hex nuts (MS51967-8).
flat head wood screws (MS35492-76). Secure general
(10) Position strap loop (MS51939- 3) on storage
mechanic tool kit to table top, using one 66-in. long
cabinet wall in accordance with figures 16 and 18. Using
retaining strap (7550588- 9). Secure padlock (5340-00-
strap loop as a template, mark and drill two 0.22-in.
682-1508) on general mechanic tool kit.
diameter holes in storage cabinet wall. Secure strap
loop (MS51939-3) to storage cabinet wall, using two #10
(6) Position armature test set (6625-00-238-
x 1/2-in. counter- sunk head machine screws (MS35190-
1459) on table top (11021224) in accordance with figure
271), two #10 lockwashers (MS35338-43), and two #10
14. Using armature test set as a template, mark and drill
hex nuts (MS35649-202).
three 0.34-in. diameter holes through base of armature
(11) Position electrical power cable assembly
test set and table top. Secure armature test set to table
(6150-00-682-3460) and extension light (6230-00-729-
top, using three 5/16- x 1-3/4- in. hex head capscrews
9259) on installed 3/8- x 5-in. square neck bolt in
(MS90725-39), three 11/32-in. flat washers (MS27183-
accordance with figures 14 and 16. Secure electrical
12), three 5/16-in. lockwashers (MS35338- 45), and
cable assembly and extension light to 3/8- x 5-in. square
three 5/16-in. hex nuts (MS51967-5).
neck bolt and storage cabinet, using one 12-in. retaining
(7) Position engine distributor tester (4910-00-
strap (7550588-6).
392-2939) on table top (11021224) in accordance with
(12) Position two-wheeled hand truck (3920-01-
052-8327) to rear right side wall in accordance with
holes in bottom of engine distributor tester base. Using
the engine distributor tester base as a template, mark
72-in. retaining strap (7550588- 1).
and drill four 0.22-in. diameter pilot holes through table
(13) Position mounting bracket of fire
top. Secure engine distributor tester to table top, using
extinguisher (4210-00-202-7858) on right front side wall
four 5/16- x 1-in. hex head lag bolts (MS16992-520) and
in accordance with figures 14 and 18. Mark and drill
four 11/32-in. flat washers (MS27183-12).
three 0.22-in. diameter holes in mounting bracket.
(8) Position revolving stool (7110-00-634-8596)
Position mounting bracket over the installed #10 blind
on rear right wall in accordance with figures 14 and 16.
rivet nuts in accordance with figure 18. Secure mounting
Secure revolving stool, using 30-in. retaining strap
bracket to right front wall, using three #10 x 1/2-in.
(7550588-8).
countersunk head machine screws (MS35190-271).
CAUTION
Install fire extinguisher in mounting bracket.
Be sure cabinet drawers adjacent to
(14) Remove contents of general purpose first
hole locations are removed before
aid kit (6545-00-922- 1200). Mark and drill three 0.22-in.
diameter holes in the back of general purpose first aid
kit. Position on right front wall in accordance with
(9) Mark and drill one 0.41-in. diameter
hole in front right storage cabinet wall in
accordance with figure 18. Secure 3/8- x 5-in.
square neck bolt (MS35751-83) to front right
13
