NOTE See     paragraph     6-6     for     disassembly procedures   on   the   air   section   of   the Type     II     panel     Figure     7-5     shall     be referred to for component location Follow number sequence for disassembly and assembly. b. Type  II  -  Oxygen  section  of  the  Type  II  control panel (see Figure 7-5) Any   disassembly,   cleaning,   inspection, repair or replacement and assembly of a part  or  parts  of  an  oxygen  system  shall be done in a contaminant free area. (a)   Disassembly Disassemble the oxygen section of the   Type   II   control   panel   only   to   the   extent necessary to repair or replace a defective part or parts. NOTE Tag   tube   assemblies   for   re-assembly purposes. (1) Disconnect and remove cam lever  valve  to pressure gauge tube assemblies (1, Figure 7-5, Sheet 2 of 2). (2) Disconnect and remove cam lever  valve  to supply  manifold  tube  assemblies  (2). (3) Disconnect  and  remove  recharge  valve  to supply   manifold   tube   assembly   (4),   and recharge valve to oxygen panel mount tube assembly (3). (4) Disconnect  and  remove  supply  manifold  to supply manifold shut-off valve tube assembly (5). (5) Disconnect  and  remove  pressure  regulator to  service  pressure  gauge  tube  assembly (7). (6) Disconnect  and  remove  pressure  regulator to     scuba     manifold     shut-off     valve     tube assembly (6) Disconnect and remove shutoff     valve     to     scuba     manifold     tube assembly (8). (7) Disconnect  and  remove  scuba  manifold  to bleed valve tube assembly (9). (8) Disconnect  and remove scuba manifold to charging valve tube assemblies (10). Disconnect  and  remove  scuba  manifold  to scuba manifold pressure gauge tube assembly (11). (9) Loosen and remove oxygen cylinder pressure gauge (13, Figure 7-5, Sheet 1 of 2)   mounting   screws   and   nuts      Remove gauge (13) from panel. (10)   Loosen  and  remove  cam  lever  valve  (14) holddown    nut,    and    remove    valve    with washer (18) from the rear of the panel. (11)   Remove   screws   (17),   and   cap   (15)   from oxygen  recharge  panel  mount  (23,  Figure 7-5,  Sheet  2  of  2)  Remove  oxygen  panel mount  from  rear  of  panel  Remove  adapter (16, Figure 7-5, Sheet 1 of 2) from mount. (12)   Remove    screws    (18)    and    washers    (19) from oxygen supply manifold (24, Figure 7- 5,  Sheet  2  of  2)  and  scuba  manifold  (28) Remove   manifolds   from   the   rear   of   the panel  Remove  manifold  mounts  (20),  and safety    valves    (21)    from    the     manifolds Remove  connectors  (19,  22  and  27)  from the supply and scuba manifolds. (13)   Loosen and unscrew valve (20, Figure 7-5, Sheet  1  of  2)  retaining  nut  Pull  handle  of valve  steadily  outward,  while  steadying  the back   portion   of   the   valve   Remove   rear sections of the valve with washer (25) from the panel. (14)   Remove pop off cap from handle of oxygen pressure   regulator   (22),   remove   nut   and handle,   remove   screws   (21)   from   panel mount  and  remove  regulator  from  the  rear of the panel. (15)   Loosen  and  remove  mounting  screws  and nuts   to   oxygen   regulator   pressure   gauge (23) Remove gauge. (16)   Loosen   and   remove   screws   and   nuts   to scuba manifold pressure gauge (24). Remove gauge b. Inspection: (1) Type II (Air) Section of Control Panel - See paragraph 6-6.c. for Inspection instructions 6-10