TB 9-4910-745-30
3. Installation-Continued
d. Unit 2. Follow steps 1 thru 12
below for equipment installation.
(21) Secure disk sander (5130-OO-
NOTE
857-8526) to top slat of truck rack
Fabricate the 74-in. support
using 24-in. retaining strap (7550588-
angle as shown in figure 23.
5) in accordance with figure 2.
(22) Position utility grinding
(1) Position 74-in. support angle
(11021151-2) on trailer floor in accord-
machine (3415-00-517-7754) on top of
11-drawer storage cabinet in accordance
for dimensions. Mark and drill thirteen
with dimensions shown in figure 2.
Using utility grinding machine base as
0.31-in. diameter holes through 74-in.
support angle and trailer floor.
a template, mark and drill three 0.37-
in. diameter holes through n-drawer
Secure 74-in. support angle to trailer
floor with thirteen 5/16- x 1-1/4-in.
storage cabinet top. Secure utility
hex head capscrews (MS90725-35),
grinding machine with three 5/16- x
2.00-in. hex head capscrews (MS90725-
thirteen 5/16-in. lockwashers (MS35338-
45), and thirteen 5/16-in. hex nuts
40), three 5/16-in. flat washers
(MS51967-5).
(MS27183-11), three 5/16-in. lock-
washers (MS35338-45), and three 5/16-
(2) Stow the six motor vehicle
in. hex nuts (MS51967-5).
trestles (4910-00-262-0392) between 74-
(23) Position machinist's vise
in. support angle and front wall of
trailer, as shown in figure 9.
(5120-00-293-1439) on 11-drawer storage
cabinet top in accordance with dimensions
(3) Position hydraulic jack kit
in figure 2. Using machinist's vise
(5120-00-595-8388) against 74-in.
base as a template, mark and drill four
support angle (11021151-2) and 18
0.50-in. diameter holes through 11-
inches from left side of trailer.
drawer storage cabinet top. Secure
Refer to figure 9 for dimensions and
machinist's vise to 11-drawer storage
cabinet top with four 1/2- x 2-3/4-in.
location.
hex head Capscrews (MS90725-118), four
1/2-in. flat washers (MS27183-17), four
(4) Position three oxygen cylinders
1/2-in. lockwashers (MS35338-48), and
(8120-00-151-9758) in trailer as shown
four 1/2-inch hex nuts (MS51967-14).
mounting dimensions. Secure oxygen
(24) Position generator test set
cylinders to trailer wall and rack with
(4910-00-092-9136) and tachometer-dwell
six 36-in. retaining straps (7550588-4)
test set (4910-00-788-8549) on top of
in accordance with figure 11.
tube-pipe fitting kit in accordance
with figure 2. Secure test sets to
(5) Position mechanic's creeper
truck wall with 72-in. retaining strap
(4910-00-251-6981) on top of trailer
(7550588-1).
right side wheel well as shown in
(25) Position separator (4940-00-
with two 92-in. retaining straps
242-4100) centered on top slat of truck
(7550588-7).
rack in accordance with dimension in
(6) Position tool box (5140-01-
template, drill two 0.12-in. diameter
119-2516) on top of trailer left side
pilot holes in slat. Secure separator
wheel well as shown in figure 13 and
bracket to slat with two #14 x 7/8-in.
secure to trailer wall and floor with
round head wood screws (MS35493-102),
two 92-in. retaining straps (7550588-
and two 1/4-in. lockwashers (MS35338-
7).
44).
12
