0036 00
TM 1-4920-433-13&P
REMOVAL CONTINUED
4 DRAWER CABINET (C) AND 4 DRAWER CABINET (D) CONTINUED
5.
Remove work surface (Figure 4, Item 18) from top of cabinet (C) (Figure 4, Item 7) and cabinet (D) (Figure 4,
Item 6).
6.
Remove four bolts (Figure 4, Item 19), four lock washers (Figure 4, Item 3), and eight lat washers (Figure 4,
Item 20) and four nuts (Figure 4, Item 22) detaching two cabinet brackets (Figure 4, Item 21) from cabinet (C)
(Figure 4, Item 7) and cabinet (D) (Figure 4, Item 6).
7.
Remove four bolts (Figure 4, Item 19), four lock washers (Figure 4, Item 3), eight lat washers (Figure 4, Item
2), and four nuts (Figure 4, Item 22) detaching cabinet (C) (Figure 4, Item 7) from cabinet (D) (Figure 4, Item
6).
REPAIR OR REPLACEMENT
4 DRAWER CABINET (C) AND 4 DRAWER CABINET (D)
1.
If cabinet brackets (Figure 4, Item 21) can be repaired by welding, weld damaged area IAW TM
1-1500-204-23. Repair must not interfere with form, it, or function of cabinet brackets (Figure 4, Item 21).
2.
Paint repaired cabinet brackets (Figure 4, Item 21) IAW (WP 0058 00, Figure 1).
INSTALLATION
4 DRAWER CABINET (C) AND 4 DRAWER CABINET (D)
1.
Install four bolts (Figure 4, Item 19), eight large lat washers (Figure 4, Item 2), four lock washers (Figure 4,
Item 3), and four nuts (Figure 4, Item 22) securing cabinet (C) (Figure 4, Item 7) to cabinet (D) (Figure 4, Item
6).
2.
Install four bolts (Figure 4, Item 19), eight large lat washers (Figure 4, Item 20), four lock washers (Figure
4, Item 3), and four nuts (Figure 4, Item 22) securing two cabinet brackets (Figure 4, Item 21) to cabinet (C)
(Figure 4, Item 7) and cabinet (D) (Figure 4, Item 6).
3.
If a new work surface (Figure 4, Item 18) must be installed:
a.
Position work surface (Figure 4, Item 18), inished side up, on top of cabinet (C) (Figure 4, Item 7) and
cabinet (D) (Figure 4, Item 6).
b.
Ensure work surface (Figure 4, Item 18) is lush with the side and back of cabinet (C) (Figure 4, Item 7)
and cabinet (D) (Figure 4, Item 6).
c.
On inside of cabinet (C) (Figure 4, Item 7) , mark four hole placements (Figure 4, Item 1) in top of cabinet
on non-inished side of work surface (Figure 4, Item 18).
d.
On inside of cabinet (D) (Figure 4, Item 6), mark two hole placements (Figure 4, Item 5) in top of cabinet
(D) (Figure 4, Item 6) on non-inished side of work surface (Figure 4, Item 18).
e.
After four hole placement marks have been made, lip work surface (Figure 4, Item 18) over with non-
inished side up.
f.
On non-inished side of work surface (Figure 4, Item 18) at four marked hole placements, center punch
and drill four 5/16 inch holes to a depth of 3/4 inch.
g.
Return work surface (Figure 4, Item 18) inished side up, on top of cabinet (C) (Figure 4, Item 7) and
cabinet (D) (Figure 4, Item 6).
4.
Align bolt holes of work surface (Figure 4, Item 18) with bolt holes on top of cabinet (C) (Figure 4, Item 7) and
cabinet (D) (Figure 4, Item 6).
5.
Install four lag bolts (Figure 4, Item 4), four lock washers (Figure 4, Item 3), and four lat washers (Figure 4,
Item 2) securing work surface (Figure 4, Item 18) to six drawer cabinet (C) (Figure 4, Item 7) and cabinet (D)
(Figure 4, Item 6).
6.
If new cabinet (C) (Figure 4, Item 7) and/ or cabinet (D) (Figure 4, Item 6) has been installed:
0036 00-8
