TM   55-4920-402-13&P Table  4-11.  DC  Cables  Resistance  Checks From (+) I To  (–) I Resistance DC Extension cable A3529 Pin A (male end) Pin A (female end) Less than 1 ohm Pin B (male end) Pin B (female end) Less than 1 ohm Shell  (male  end) Pin A or B More than 10 M Shell  (female  end) Pin A of B More than 10 M Pin A (male end) Pin B (male end) More than 10 M DC Adapter cable B3140-1 Silver pin (male end) Pin A (female end) Less than 1 ohm Cold  pin  (male  end) Pin B (female end) Less than 1 ohm Shell (male end) Pin A or B More than 10 M Shell  (female  end) Pin A or B More than 10 M Pin A (female end) Pin B (female end) More than 10 M DC Adapter cable B3140-5 Black  clip Pin A (female end) Less than 1 ohm Red clip Pin B (female end) Less than 1 ohm Shell  (female  end) Pin A or B More than 10 M Pin A (female end) Pin B (female end) More than 10 M DC Adapter Cable B3140-9 Pin A (female end) Lamp Shell Less than 1 ohm Pin B (female end) Lamp center conductor Less than 1 ohm Shell  (female  end) Pin A or B More than 10 M Pin A (female end) Pin B (female end) More than 10 M 4-16. DC Cables. These tests will deterrrdne the opera- perform additional resistance checks from the circuit card tional  capability  of  the  DC  Extension  Cable  and  DC  Adap- to related components. ter Cables. Refer to figures 4-9 and 4-10 for schematic diagrams of the DC Extension Cable and DC Adapter Ca- bles  end  perform  resistance  checks  in  accordance  with table  4-11. 4-17. Signal Simulator. These tests will determine the ope- rational capability of the Signal Simulator. Refer to figure 4-11  for  a  schematic  diagram  of  the  Signal  Simulator  and perform  resistance  checks  in  accordance  with  table  4-12. 4-18. Balancer Wiring Checkout.Refer to figures FO-1 and  FO-2  and  perform  additional  resistance  checks  from the circuit cards to related components. 4-19. Strobex Wiring Checkout. Refer to figure FO-3 and Table  4-12.  Signal  Simulator  B4305  Resistance  Checks From (+) P1-A P1-A P1-B P2-A P2-B P2-A P2-A P2-B P2-C To  (–) P1-B P1 (Shell) P1 (Shell) P2-B P2-C P2-C P2 (Shell) P2 (Shell) P2 (Shell) Resistance 300 to 360 ohms 300 to 360 ohms Less than 1 ohm 50 to 56 k 2.0 to 2.4 k 50 to 56 k 50 to 56 k 2.0 to 2.4 k Less than 1 ohm Section  III.  REPAIR  PROCEDURES 4-20. Removal and Disassembly. The  complete  disassem- disassembly  procedures  in  the  following  paragraphs.  Dis- bly  of  VIBREX  components;  i.e.,  circuit  cards,  transfor- assemble  only  to  extent  necessary  to  accomplish  repairs. mers, switches, etc., is not authorized at this maintenance 4-21. Disassembly of Balancer. Disassembly   instructions level. After performing the troubleshooting procedures consist of removal and replacement of the meter. Re- in  paragrapha  4-10  through  4-19,  perform  the  removal  and move the meter as follows (fig. 4-12): 4-13