TB 9-4910-744-30
i n accordance with figure 3 using T-
4.
Installation--Continued
b o l t s and nuts provided with machine
eter pilot holes into the tabletops.
table vise.
Mark and drill twelve 0.22-in. diameter
(6) Position and secure portable
pilot holes through table legs into van
floor on aisle side only (three per
electric drill (5130-00-473-6228) to
drill stand in accordance with figure
table).
Enlarge holes in table legs to
3.
0.34-in. diameter. Secure tables to
angle irons and floor of van using
(7) Position 3-in. machinist's
twenty-eight 5/16- x 1-1/4-in. hex head
v i s e (5120-00-180-0681) on top of 72-
l a g bolts (MS16992-521) and twenty-
in. table in accordance with figures 2
e i g h t 5/16-in. lockwashers (MS35338-
and 3.
Using 3-in. machinist's vise
45 ) .
base as template, mark and drill four
0.56-in. diameter holes through table-
(3) Position utility grinder
Secure 3-in. machinist's vise to
top.
(3415-00-517-7754) on 72-in. table
tabletop using four 1/2- x 3-1/4-in.
w / d r a w e r s in accordance with figures 2
h e x head capscrews (MS90725-120), four
and 4.
Using utility grinder base as
1/2-in. flat washers (MS27183-17), four
a template, mark and drill three 0.34-
1 / 2 - i n . lockwashers (MS35338-48), and
in. diameter holes through tabletop.
four 1/2-in. hex nuts (MS51967-14).
Secure utility grinder to tabletop
using three 5/16- x 2-3/4-in. hex head
(8) Position hose assembler
capscrews (MS90725-43), three 5/16-in.
f l a t washers (MS27183-11), three 5/16-
( 4 9 4 0 - 0 1 - 0 9 1 - 5 0 9 9 ) , a component of hose
assembly outfit (4940-01-080-4213), on
i n . lockwashers (MS35338-45), and three
top of 60-in. table in accordance with
5/16-in. hex nuts (MS51967-5).
figures 2 and 4.
U s i n g hose assembler
base as template, mark and drill four
(4) Position valve face grinding
0.41-in. diameter holes through table-
machine (4910-00-540-4679) on top of
S e c u r e hose assembler to tabletop
top.
72-in. table w/drawers in accordance
using four 3/8- x 2-1/4-in. hex head
with figures 2 and 4.
Using valve face
capscrews (MS90725-67), four 3/8-in.
grinding machine base as a template,
flat washers (MS27183-13), four 3/8-in.
mark and drill two 0.56-in. diameter
I o c k w a s h e r s (MS35338-46), and four 3/8-
holes through tabletop. Secure valve
in. hex nuts (MS51967-8).
face grinding machine to tabletop using
t w o 1/2- x 3-1/4-in. hex head capscrews
{ M S 9 0 7 2 5 - 1 2 0 ) , two 1/2-in. flat washers
(9) Position three mechanic's
( M S 2 7 1 8 3 - 1 7 ) , two 1/2-in. lockwashers
creepers (4910-00-251-6981) upright
( M S 3 5 3 3 8 - 4 8 ) , and two 1/2-in. hex nuts
against front wall in accordance with
(MS51967-14).
S e c u r e to front w a l l
figures 2 and 5.
using two 92-in. retaining straps
(5) Position drill stand (5130-
(7550588-7).
00-263-8657) on top of 60-in. table in
accordance with figures 2 and 3.
Using
(10) Position four trestles (4310-
drill stand base as a template, mark
00-251-8013) in rear van corners in
and drill three 0.38-in. diameter holes
through tabletop.
Secure drill stand
Secure using two 36-in. retaining
to tabletop using three 5/16- x 2-3/4-
s t r a p s (7550588-4) passed around one
i n . hex head capscrews (MS90725-43),
table leg.
three 5/16-in. flat washers (MS27183-
11), three 5/16-in. lockwashers
(11) Stow two radiator filling
( M S 3 5 3 3 8 - 4 5 ) , and three 5/16-in. hex
cans (7240-00-499-8028), three portable
n u t s (MS51967-5).
S e c u r e machine table
electric drills (5130-00-473-6228), 30-
vise (3460-00-277-3504) to drill stand
13
