TB 9-4910-744-30
4.
Installation--Continued
(3) Mark and drill twenty 0.22-
in. diameter holes in the front and
left wall slats in accordance with
(13) Mark and drill four 0.09-in.
figures 19 and 20. Secure ten strap
diameter pilot holes on rear storage
l o o p s (MS51939-3) using twenty #10 x 1-
cabinet top in accordance with figure
1 / 4 - i n . counter head machine screws
13. Position and secure two strap
(MS35190-276), twenty 7/32-in. flat
l o o p s (MS51939-3) using four #10 x 1-
w a s h e r s (MS27183-42), twenty #10
in. flat head wood screws (MS35492-78).
l o c k w a s h e r s (MS35338-43), and twenty
#10-32UNF hex nuts (MS35650-302).
( 1 4 ) Position ten wash pans on
r e a r storage cabinet top in accordance
f.
Follow steps (1) thru (15) below
with figures 7 and 9. Secure to cabinet
for equipment installation in unit 3.
top using 110-in. retaining strap
(7550588-10).
(1) Position two 72-in. tables
(4910-00-357-5342) against the right
(15) Position transmission and
side wall in accordance with figure 15.
differential lift (4910-00-585-3622) on
Mark and drill sixteen 0.34-in. diam-
rear floor in accordance with figures 7
e t e r holes through table leg pads and
and 8.
S e c u r e to floor using two 92-
truck floor in accordance with figure
in. retaining straps (7550588-7).
Secure 72-in. tables to floor
18.
Follow steps (1) thru
using sixteen 5/16- x 1-1/4-in. hex
( 3 ) b e l o w for b l i n d r i v e t n u t a n d s t r a p
h e a d capscrews (MS90725-36), thirty-two
loop installation.
11/32-in. flat washers (MS27183-12),
s i x t e e n 5/16-in. lockwashers (MS35338-
NOTE
45), and sixteen 5/16-in. hex nuts
Position floor- and cabinet
(MS51967-5).
t o p - m o u n t e d equipment as
shown in figures 15 and 17.
(2) Mark and drill two 0.44-in.
U s e equipment mounting holes
diameter holes in the front corners of
as a template for location of
e a c h bottcm plate of three storage
drilled mounting holes in
cabinets (7125-00-330-0130) allowing
accordance with figure 18.
f o r minimum required clearance for 3/8-
Position the
i n . hex head capscrews.
three storage cabinets in left rear
(1) Mark and drill fourteen 0.25-
corner of truck in accordance with
in. diameter holes in front and left
figures 15 and 17. Using the storage
w a l l in accordance with figures 19 and
c a b i n e t bases as templates, mark and
20. Install fourteen #10-32UNF blind
drill six 0.44-in. diameter holes
r i v e t nuts (A10-180). Secure seven strap
through truck floor in accordance with
loops (MS51939-3) to blind rivet nuts
S e c u r e storage cabinets to
u s i n g fourteen #10-32UNF x 1-in counter
floor using six 3/8- x 1-1/8-in. hex
h e a d machine screws (MS35191-276).
h e a d capscrews (MS90725-61), six 3/8-
in. flat washers (MS27183-13), six 3/8-
(2) Mark and drill four 0.22-in.
i n . lockwashers (MS35338-46), and six
diameter holes through floor in accord-
3/0-in. hex nuts (MS51967-8).
S e c u r e two strap
ance with figure 18.
loops (MS51939-3) to floor using four
(3) Mark and drill two 0.19-in.
diameter holes through right side wall
# 1 0 - 3 2 U N F x 1-in. counter head machine
o f storage cabinet in accordance with
s c r e w s (MS35191-276), four #10 lock-
S e c u r e one strap loop
w a s h e r s (MS35338-43), and four #10-32UNF
h e x nuts (MS35650-302).
16
