TB 9-4910-744-30
4.
Installation--Continued
(4) Position two grease bucket
pumps (4930-00-244-4859) against right
side wall in accordance with figures 29
NOTE
and 30.
Secure to wall using two 48-in.
Position floor-mounted
retaining straps (7550588-3).
e q u i p m e n t as shown in fig-
u r e s 29, 30, and 31. Use
(5) Position steam cleaner (4940-
e q u i p m e n t mounting holes as
00-186-0027) in center of trailer in
template for location of
accordance with figures 29, 30, and 31.
drilled mounting holes in
U s i n g the steam cleaner skid as tem-
accordance with figure 32.
plate, mark and drill eight 0.38-in.
diameter holes through trailer floor in
Mark and drill twelve 0.25-in. diameter
accordance with figure 32. Secure steam
holes in the right and left side walls
cleaner to floor using four 5/16-in. U-
in accordance with figures 33 and 34.
bolts (8875T37), eight 5/16-in.
Install twelve #10-32UNF blind rivet
lockwashers (MS35338-45), and eight
n u t s (A10-180). Secure six strap loops
5/16-in. hex plain nuts (MS51972-2).
( M S 5 1 9 3 9 - 3 ) to walls using twelve #10-
3 2 U N F x 1-in. counter head machine
Follow steps (1) thru
s c r e w s (MS35191-276).
(3)below
for
blind
rivet
nut
and
strap
loop installation.
Follow steps (1) thru (5) below
for equipment installation in unit 5.
NOTE
Position floor-mounted
(1) Position separator (4940-00-
e q u i p m e n t as shown in fig-
242-4101) on front right corner slat in
u r e s 35, 37, and 38. Use
accordance with figures 29 and 30.
e q u i p m e n t mounting holes as
U s i n g separator mounting bracket as
template for location of
template, mark and drill two 0.12-in.
drilled mounting holes in
diameter pilot holes in trailer slat in
accordance with figure 36.
accordance with figure 34.
Secure
separator to slat using two #14 x 7/8-
(1) Mark and drill twelve 0.25-
in. round head wood screws (MS35495-
in. diameter holes in right and left
1 2 5 ) and two 1/4-in. lockwashers
side walls in accordance with figures
(MS35338-44).
37 and 38. Install twelve #10-32UNF
(2) Position compressor (4310-
blind rivet nuts (A10-180). Secure six
00-542-4566) in front of trailer in
s t r a p loops (MS51939-3) to walls using
accordance with figures 29 and 30.
t w e l v e #10-32UNF x 1-in. counter head
U s i n g holes in compressor legs as
m a c h i n e screws (MS35191-276).
template, mark and drill four 0.56-in.
diameter holes through floor in accord-
(2) Mark and drill four 0.22-in.
ance with figure 32. Secure compressor
diameter holes through floor in accord-
to floor using four 1/2- x 2-in. hex
ance with figure 36. Secure two strap
h e a d capscrews (MS90725-115), four 1/2-
loops (MS51939-3) to floor using four
i n . lockwashers (MS35338-48), and four
# 1 0 - 3 2 U N F x l-in. counter head machine
1/2-in. hex nuts (MS51967-14).
s c r e w s (MS35191-276), four #10 lock-
w a s h e r s (MS35338-43), and four #10-32UNF
(3) Position lubricating unit
h e x nuts (MS35650-302).
(4930-00-720-4849) against the front
(3) Mark and drill eight 0.22-in.
left wall in accordance with figures 29
diameter holes through right and left
and 31.
Secure to wall using 48-in.
side wall slats in accordance with
retaining strap (7550588-3).
19
