TB 9-4910-744-30
(8) Mark and drill four 0.25-in.
4.
Installation--Continued
diameter holes in side of storage
and dolly-type jack in accordance with
cabinet in accordance with figure 14.
Secure dolly-type jack and
Install four #10-32UNF blind rivet nuts
ground rods to floor using two 66-in.
( A 1 0 - 1 8 0 ) . Position and secure two strap
retaining straps (7550588-9).
l o o p s (MS51939-3) in accordance with
figure 7 to blind rivet nuts using four
(4) Position four trestles (4910-
# 1 0 - 3 2 U N F x 1-in counter head machine
00-251-8013) next to arbor press in
s c r e w s (MS35191-276).
accordance with figures 7 and 8.
(9) Position two 12-ton hand
Secure to floor of truck using 110-in.
retaining strap (7550588-10).
hydraulic jacks (5120-00-224-7330)
against front wall in accordance with
Secure to front wall
(5) Position two drain pans
figures 7 and 8.
using 48-in. retaining strap (7550588-
( 4 9 1 0 - 0 0 - 3 8 7 - 9 5 9 2 ) on the right side
3).
w o o d slats in accordance with figures 7
and 8.
S e c u r e drain pans to wood slats
using two 66-in. retaining straps
(10) Position two engine transport
(7550588-9).
stands (4910-00-338-6673) against front
left wall in accordance with figures 7
(6) Position brake drum lathe
Secure to wall, floor, and
and 9.
(4910-01-028-9849) in accordance with
storage cabinet side using two 36-in.
retaining straps (7550588-4) and four
figures 7 and 8.
Using brake drum
lathe base as template, mark and drill
48-in. retaining straps (7550588-3) in
four 0.50-in. diameter holes through
a c c o r d a n c e with figures 7 and 9. Two
truck floor in accordance with figure
of the 48-in. retaining straps are
wrapped around truck slats.
S e c u r e brake drum lathe to floor
10.
using four 7/16- x 1-1/4-in. hex head
capscrews (MS90725-87), four 7/16-in.
(11) Position 3-in. machinist's
f l a t washers (MS27183-15), four 7/16-
vise (5120-00-180-0681) and 4-in.
i n . lockwashers (MS35338-47), and four
machinist's vise (5120-00-293-1439) on
7/16-in. hex plain nuts (MS51967-11).
e d g e s of storage cabinets in accordance
with figures 7 and 9. Using vise bases
(7) Mark and drill two 0.44-in.
as templates, mark and drill eight
diameter holes in the front corners of
0.56-in. diiameter holes through tops of
bottam plates of three storage cabinets
S e c u r e 3-in. and 4-
storage cabinets.
(7125-00-330-0130), allowing for
in. machinist's vises to cabinet tops
minimum required clearance for 3/8-in.
using eight 1/2- x 3-1/4-in. hex head
hex head capscrews. Position the three
c a p s c r e w s (MS90725-120), eight 17/32-
storage cabinets in left rear corner of
in. flat washers (MS27i83-18), eight
t r u c k in accordance with figures 7 and
1 / 2 - i n . lockwashers (MS35338-48), and
9 . U s i n g the storage cabinet bases as
eight 1/2-in. hex nuts (MS51967-14).
templates, mark and drill six 0.44-in.
diameter holes through truck floor in
(12) Position generator test set
accordance with figure 10. Secure
( 4 9 1 0 - 0 0 - 0 9 2 - 9 1 3 6 ) on top of storage
storage cabinets to floor using six
cabinets in accordance with figures 7
3 / 8 - x 1-1/8-in. hex head capscrews
Secure to storage cabinet
and 9.
(MS90725-61), six 3/8-in. flat washers
d r a w e r handle and truck slat using 110-
( M S 2 7 1 8 3 - 1 3 ) , six 3/8-in. lockwashers
11, retaining strap (7550588-10).
( M S 3 5 3 3 8 - 4 6 ) , and six 3/8-in. hex nuts
(MS51967-8).
15
