TB 9-4910-744-30
4.
Installation--Continued
(11) Position hoisting unit (4910-
0 0 - 4 4 8 - 0 2 5 4 ) on truck floor between 72-
( M S 5 1 9 3 9 - 3 ) to storage cabinet side
in. tables and storage cabinets in
using two 3/16-in. blind rivets
accordance with figures 15 and 16.
(MS20601-MP6W2).
Secure hoisting unit to table cross
brace using 36-in. retaining strap
(4) Position three oxygen cyl-
(7550588-4.
)
inders (8120-00-151-9758) on front wall
Secure
in accordance with figure 15.
(12) Position 4-in. machinist's
to wall using six 36-in. retaining
v i s e (5120-00-293-1439) on top of rear
72-in. table in accordance with figures
straps (7550588-4) in accordance with
Using 4-in. machinist's
15 and 16.
vise base as a template, mark and drill
four 0.56-in. diameter holes through
(5) Position dolly-type jack
Secure 4-in. machinist's
(4910-00-289-7233) on front floor next
tabletop.
t o the oxygen cylinders and under the
vise to tabletop using four 1/2- x 3-
1 / 4 - i n . hex head capscrews (MS90725-
72-in. table in accordance with figure
15.
Secure dolly-type jack to floor in
120), four 1/2-in. flat washers
(MS27183-17), four 1/2-in. lockwashers
accordance with figure 16 using 36-in.
retaining strap (7550588-4).
( M S 3 5 3 3 8 - 4 8 ) , and four 1/2-in. hex nuts
(MS51967-14).
(6) Position degreaser (4940-00-
449-6689) in front left corner of truck
(13) Position disk sander (5130-
in accordance with figures 15 and 17.
00-857-8526) on top of 72-in. table in
Secure to wall slats using 110-in.
accordance with figures 15 and 16.
retaining strap (7550588-10).
Secure to truck slat using 24-in.
retaining strap (7550588-5).
(7) Position four trestles (4910-
00-251-8013) between right side of
(14) Position transmission and
differential lift (4910-00-585-3622) on
s t o r a g e cabinet and degreaser in ac-
cordance with figures 15 and 17.
rear floor of truck in accordance with
figures 15 and 16.
S e c u r e transmission
Secure trestles to storage cabinet and
and differential lift to 72-in. table's
truck wall using 36-in. retaining strap
cross brace using 36-in. retaining
(7550588-4).
strap (7550588-4).
(8) Position five mechanic's
creepers (4910-00-251-6981) under 72-
(15) Position hand truck (3920-01-
in. table in accordance with figures 15
113-0117) in rear left corner in accord-
and 16.
S e c u r e to table leg using 30-
ance with figures 15 and 17. Secure
acetylene cylinder (8120-00-268-3360)
in. retaining strap (7550588-8).
and oxygen cylinder (8120-00-151-9758)
to hand truck in accordance with figure
(9) Position two 8-ton hand
1 5 u s i n g 9 2 - i ne r e t a i n i n g s t r a p
hydraulic jacks (5120-00-595-8396)
under 72-in. table in accordance with
( 7 5 5 0 5 8 8 - 7 ) . Secure hand truck with
figures 15 and 16.
Secure to table leg
a c e t y l e n e and oxygen cylinders to truck
using 36-in. retaining strap (7550588-
slats using 92-in. retaining strap
4).
(7550588-7).
F o l l o w steps (1) and
(10) Position six 20-ft extension
lights (6230-00-268-9436) and two 7-ft
(2) below for blind rivet nut and strap
loop installation.
power cable assemblies (4910-00-800-
1 4 0 5 ) on truck slat in accordance with
figures 15 and 16.
Secure using eight
24-in. retaining straps (7550588-5).
17
