TB 9-4910-744-30
(3) Position separator (4940-00-
4.
Installation--Continued
242-4101) on slat in front right wall in
accordance with figures 23 and 24.
NOTE
U s i n g separator mounting bracket as
Position floor-mounted
template, mark and drill two 0.12-in.
e q u i p m e n t as shown in
diameter pilot holes in slat in accord-
figures 23, 24, and 25.
Use
ance with figure 27. Secure separator
e q u i p m e n t mounting holes as
to slat using two #14 x 7/8-in. round
template for location of
head wood screws (MS35495-125) and two
drilled mounting holes in
1/4-in. lockwashers
(MS35338-44).
accordance with figure 26.
(4) Position 4-qt liquid measure
(1) Mark and drill eighteen
(7240-00-233-6015) in front right corner
0.25-in. diameter holes in right and
of trailer in accordance with figures 23
left side walls of trailer in accord-
and 24.
Secure to right wall using 24-
ance with figures 27 and 28.
Install
in. retaining strap (7550588-5).
eighteen #10-32UNF blind rivet nuts
( A 1 0 - 1 8 0 ) . Secure nine strap loops
(5) Position lubricating unit
( M S 5 1 9 3 9 - 3 ) using eighteen #10-32UNF x
(4930-00-720-4849) against `left front
1 - i n . counter head machine screws
w a l l in accordance with figures 23 and
(MS35191-276).
25. Secure to wall using 48-in. re-
t a i n i n g strap (7550588-3).
(2) Mark and drill two 0.22-in.
diameter holes through trailer floor in
accordance with figure 26. Secure
(6) Position two oil bucket pumps
(4930-00-244-4860) against right side
strap loop (MS51939-3) to floor using
w a l l in accordance with figures 23 and
t w o #10-32UNF x 1-in. counter head
24. Secure to wall using two 48-in.
m a c h i n e screws (MS35191-276), two #10
retaining straps (7550588-3).
l o c k w a s h e r s (MS35338-43), and two #10-
32UNF hex nuts (MS35650-302).
(7) Position diesel engine gen-
erator set (6115-00-465-1044) in rear of
h.
Follow steps (1) thru (8) below
trailer in accordance with figure 23.
for equipment installation in unit 4.
U s i n g diesel engine generator set base as
template, mark and drill four 0.62-in.
(1) Position compressor (4310-
diameter holes through floor in accord-
00-542-4566) in front of trailer in
ance with figure 26. Secure diesel
accordance with figures 23 and 24.
engine generator set to floor using four
U s i n g holes in compressor legs as
1 / 2 - x 1-1/2-in. hex head capscrews
template, mark and drill four 0.56-in.
( M S 9 0 7 2 5 - 1 1 3 ) , four 1/2-in. lockwashers
diameter holes through floor in accord-
( M S 3 5 3 3 8 - 4 8 ) , and four 1/2-in. hex nuts
ance with figure 26.
S e c u r e compressor
(MS51967-14).
to floor using four 1/2- x 2-in. hex
h e a d capscrews (MS90725-115), four 1/2-
i n . lockwashers (MS35338-48), and four
(8) Position tool box (5140-00-
315-2758) on rear left corner floor in
1/2-in. hex nuts (MS51967-14).
accordance with figure 23.
Secure to
trailer wall and floor using 48-in.
(2) Position motor vehicle
retaining strap (7550588-3).
e n g i n e and transmission sling (4910-00-
944-4915) against trailer wall in front
F o l l o w the procedure
i.
left corner in accordance with figures
Unit 5.
below for blind rivet nut and strap loop
23 and 25.
Secure to trailer slat
installation.
using 24-in. retaining strap (7550588-
5).
18
