NOTE This occurs when actuation point of switch is adjusted for 3, 200 psig (22, 348 KPa). (d) Slowly    increase    pressure    above    3, 350 psig.  Indicator A should light. (e) If  lamp  does  light  within  the  specified limits, adjust actuation point of pressure switch by loosening lockscrew     and     turning     adjustment screw  clockwise  to  lower actuation point  or counterclockwise  to raise it. (f) Repeat steps b through e until indicators   light   within   the   specified limits. (g) If correct indication cannot be obtained, switch is defective. d. Repair  or  Replacement.    Refer  to  paragraph  6- 3.c for general repair or replacement instructions. (1) Replace defective wiring. (2) Replace defective solenoid valve. (3) Replace defective pressure switch. e. Assembly.      To   assemble   the   unloader   control box group.  proceed as follows: (1) Disconnect  and  separate  inner  panel  from con-trol box (30). (2) Using   screws   (28),   lockwasher   (27)   and nuts   (’6)   attach   relay   (39)   to   inner   panel. Position  the  inner  panel  in  the  control  box (30). (3) Thread   wiring   (20)   through   connector   nut (18) and insert solenoid (19) wiring through hole in the side of control box (30).  Thread wiring through lock washer and connector; attach   solenoid   (19)   to   control   box (30).  If removed, install connector (17) and elbow (16) on solenoid (19). (4) Connect    solenoid    ground    wire    (20)    and diode  assembly  (21)  to  inner  panel   using attaching screw. (5) insert  pressure  switch  (14)  through  hole  in front  of  control  box  (30),  and  attach  switch to  control  box  using  washer  and  nut  (14). Screw adaptor    (13)    into    pressure    switch    (14). Snap in plug (12). (6) Using    screw    (11)    attach    terminal    (22), washer    (9),    and    insulated    washer    (10); insert  through  hole   No.      I   in   control   box. Attach     washer     (10),     washers     (9)     lock washer (8) and nut (7) to screw (11). (7) Using    screw    (11)    attach    terminal    (25), washer    (9)    and    insulated    washer    (10); insert   screw   (1)   through   hole   No.      2   in control  box.    Attach  washer  (10),  washers (9),  lock  washer  (8)  and  nuts  (7)  to  screw (11). (8) Using   screw   (1   I1)   attach   terminal   (24), washer   (9),   insulated   washer   (10);   insert screw  (11)  through  hole  No.    3  in  control box.  Attach washer (10), washers (9), lock washer (8) and nuts (7) to screw (11). (9) Using   screw   (   1)   attach   terminals   (I   5), washer    (9),    and    insulated    washer    (10); insert   screw   (11)   through   hole   No.      4   in control  box.    Attach  washer  (10),  washers (9),  lock  washer  (8)  and  nuts  (7)  to  screw (11). (10)   Using screw (11) attach terminals (15.  20, and 21), washer (9), insulated washer (10), insert   screw   (II)   through   hole   No.      5   in control   box.      Attach   washer   (10),   washer (9),  lock  washer  (8)  and  nuts  (7)  to  screw (11). (11)   Attach     shock     mounts     (3)     to     mounting brackets  (5)  using  lock  washer  (2)  and  nut (4). (12)   Attach   unloader   control   assembly    (7)    to shock mounts (3) using lock washer (2) and nuts (1). 6-32.    Condensate  Receiver  Group  (See  Figure  8.29). The following paragraphs contain disassembly, cleaning, inspection, repair or replacement, and assembly instructions for the condensate receiver group. a. Disassembly.        Disassemble     the     condensate receiver  group  only  to  the  extent  necessary  to  repair  or replace a defective part or parts. (1) Disconnect and remove drain hose (1) and tube assembly (5).   Identify  for  reassembly purposes. (2) Unscrew    and    remove    screws    (10)    lock washer   (11),   remove   separator   cap   (12) and    gasket    (13).        Remove    elbow    (14). 6-39